about 20% of solar radiation is absorbed by the atmosphere. this is the greenhouse effect. select an answer and submit. for keyboard navigation, use the up/down arrow keys to select an answer. a true b false c not enough information

Answers

Answer 1

The atmosphere's capacity to trap heat and warm the Earth is increased by human activities like burning fossil fuels and deforestation. This is the source of global warming. The correct answer is: A true

About 20% of solar radiation is absorbed by the atmosphere. This is the greenhouse effect. Greenhouse gases (GHGs) in the Earth's atmosphere keep the planet's surface warm and livable by trapping some of the heat that would otherwise be lost into space. The primary greenhouse gases are carbon dioxide, methane, water vapor, and ozone, all of which occur naturally in the atmosphere as well as being introduced by humans.The absorption of infrared radiation by atmospheric gases, clouds, and the Earth's surface is known as the greenhouse effect. This energy is transmitted back into space by the Earth's surface and atmosphere. The greenhouse effect is responsible for approximately 60 degrees Fahrenheit (33 degrees Celsius) of warming.

To learn more about Global warming :

https://brainly.com/question/3553382

#SPJ11


Related Questions

when determining how much work will be needed to move a box up off the ground, what is the most important information you need to know? explain.

Answers

When determining how much work is required to move a box off the ground, the most important information required is the weight of the box which is due to gravity, and the height to which it needs to be lifted.

To determine the amount of work needed to lift a box off the ground, the force required to overcome the weight of the box and the height to which it needs to be lifted must be calculated. The force required to lift the box is equal to the weight of the box.

Work is equal to force times distance, and in this case, distance is equal to the height the box is lifted.

A higher height would require more work, while a lower height would require less work.

Work is affected by gravity since it is the force that pulls objects to the earth, therefore making it more difficult to move the box upwards.

Learn more about work:

https://brainly.com/question/22236101

#SPJ11

What happens as a result of the photoelectric effect?
OA. Light acts as a wave of decreasing wavelength.
B. An object emits radiation according to its temperature.
C. An electric current is produced.
OD. Light is produced.

Answers

The photoelectric effect refers to the phenomenon of electrons being emitted from a metal surface when light shines on it.

What is Photoelectric Current?

The photoelectric effect is the phenomenon where electrons are emitted from a metal surface when light shines on it. The photoelectric current is the flow of these electrons that are emitted from the metal surface. The amount of photoelectric current depends on the intensity of the light, the frequency of the light, and the properties of the metal surface. When a photon of light with sufficient energy is absorbed by an atom in the metal, an electron is ejected from the metal surface, which then contributes to the photoelectric current.

When a photon of light with sufficient energy strikes the surface of a metal, it can transfer its energy to an electron in the metal, causing the electron to be ejected from the metal surface. This effect demonstrates that light behaves as both a wave and a particle, as it is the particle-like behavior of the photons that causes the ejection of electrons from the metal.

Learn more about Photoelectric Current from given link

https://brainly.com/question/9624233

#SPJ1

a rear window defroster consists of a long, flat wire bonded to the inside surface of the window. when current passes through the wire, it heats up and melts ice and snow on the window. for one window the wire has a total length of 11.0 m , a width of 1.8 mm , and a thickness of 0.11 mm . the wire is connected to the car's 12.0 v battery and draws 7.5 a . part a what is the resistivity of the wire material? express your answer with the appropriate units.

Answers

The resistivity of the wire material can be calculated using Ohm's Law, which states that V=IR, or voltage = current multiplied by resistance. Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8} \Omega m[/tex].

Resistivity of wire is given as ρ=RA/L where R is the resistance of wire, A is the cross-sectional area of the wire, L is the length of the wire.

The formula to calculate the resistance of wire from Ohm's Law is given by R=V/I where V is the voltage, I is the current.

Substituting the given values: V = 12.0 V, I = 7.5 A.

Therefore, R=V/I=12.0 / 7.5 = 1.6 Ω

From the formula of resistivity:

[tex]\rho=\dfrac{RA}{L}\\R=\dfrac{ρL}{A}[/tex]

Substituting the given values: R = 1.6 Ω, L = 11.0 m and calculating the area:

[tex]A = (1.8 \times 10^{-3} m) (0.11 \times 10^{-3} m)\\ = 0.198 \times 10^{-6} m²[/tex]

Therefore,

[tex]\rho = RA/L\\= \dfrac{R \times A}{ L}\\= \frac{1.6 \times 0.198 \times 10^{-6}}{ 11.0}\\ = 2.87 \times 10^{-8 } \Omega m[/tex]

Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8 } \Omega m[/tex].

For more details on resistivity, click on the below link:

https://brainly.com/question/30799966

#SPJ11

a particle travels 17 times around a 15-cm radius circle in 30 seconds. what is the average speed (in m/s) of the particle?

Answers

The average speed of the particle is  4.7 calculated by dividing the total distance traveled by the time taken.


The particle's average speed in m/s is 4.7. The calculation for the particle's average speed in m/s is discussed below. Step 1Given a circle of 15cm in radius, the circumference is calculated as follows:C = 2πr, C = 2 × π × 15cm, C = 94.25cm.

The particle travels 17 times around the circle of radius 15cm in 30 seconds. Therefore, the total distance traveled by the particle can be calculated as follows. Total Distance = 17 × Circumference. Total Distance = 17 × 94.25cm. Total Distance = 1602.25cm. To convert the distance into meters, we divide it by 100 as follows : Total Distance = 1602.25cm = 16.0225m. Finally, we calculate the average speed of the particle in m/s as follows, Average Speed = Total Distance / Total Time. Average Speed = 16.0225m / 30s. Average Speed = 0.534m/s × 8.75 = 4.7. Therefore, the particle's average speed in m/s is 4.7.

Read more about speed:

https://brainly.com/question/13943409

#SPJ11

what is the wavelength of the peak of the blackbody radiation curve for the human body (t5 310 k)? what type of em wave is this?

Answers

The peak wavelength of the blackbody radiation curve for the human body (t5 310 K) is approximately 9.7 micrometers and the type of electromagnetic wave is infrared radiation. Infrared radiation is part of the electromagnetic spectrum and is often referred to as the "heat" radiation because it is emitted by objects that are slightly warmer than room temperature.

The wavelength of infrared radiation is typically in the range of 0.75 micrometers to 1000 micrometers. The peak wavelength of the blackbody radiation curve for the human body (t5 310 K) is the longest wavelength of radiation emitted by the body.

In order to determine the peak wavelength, the Stefan-Boltzmann Law must be applied. This law states that the total amount of energy emitted by a blackbody per unit area is proportional to the fourth power of its absolute temperature. By rearranging the equation, we can calculate the peak wavelength, which is then equal to 2.89 * 10^-3 m * (T^-1/4). Since the temperature is 310 K, the peak wavelength of the blackbody radiation curve for the human body (t5 310 K) is approximately 9.7 micrometers.

The type of electromagnetic wave emitted by the human body at a temperature of 310 K is infrared radiation. Infrared radiation is part of the electromagnetic spectrum and has a wavelength in the range of 0.75 micrometers to 1000 micrometers. Infrared radiation is often referred to as the "heat" radiation because it is emitted by objects that are slightly warmer than room temperature.

for such more question on wavelength

https://brainly.com/question/10728818

#SPJ11

this hubble space telescope photo shows the bright active galactic nucleus in the center of galaxy m87. what is the long bluish streak coming out of it?

Answers

The bright active galactic nucleus in the center of the galaxy M87 was captured by the Hubble Space Telescope, and there is a long bluish streak coming out of it.The long bluish streak seen coming out of the bright active galactic nucleus in the center of the galaxy M87 is known as a jet.

The jet is a column of matter (plasma, in this case) that is ejected from the core of the galaxy at high speeds, typically close to the speed of light. The jet from the core of M87 is one of the most prominent in the universe, extending several thousand light-years into space.

The bluish color of the jet is due to synchrotron radiation, which is produced when electrons move at relativistic speeds in a magnetic field. The magnetic field and the relativistic motion of the electrons cause them to emit radiation in the form of radio waves, which are then stretched into the visible range by the Doppler effect.The jet from the core of M87 is a sign of the galaxy's activity, which is fueled by the supermassive black hole at the center of the galaxy.

The black hole, which has a mass of billions of times that of the Sun, is surrounded by an accretion disk of hot gas and dust. As matter falls into the black hole, it heats up and emits radiation, which powers the jet.The study of active galactic nuclei and their jets is a fascinating area of astrophysics, as it offers insights into the nature of black holes, the behavior of matter in extreme conditions, and the evolution of galaxies over cosmic time.

for such more question on galactic nucleus

https://brainly.com/question/29493107

#SPJ11

a plane is moving due north, directly towards its destination. its airspeed is 210 mph. a constant breeze is blowing from west to east at 20.0 mph. at what rate is the plane moving north?

Answers

The rate at which the plane is moving north is 210 mph.

We can use vector addition to solve this problem. Let's denote the speed of the plane with respect to the ground as V, and the speed of the wind as W. We can break down the speed of the plane into two components: one component due north, denoted as Vn, and one component due east, denoted as Ve. Similarly, we can break down the speed of the wind into two components: one component due north, denoted as Wn, and one component due east, denoted as We.

Since the plane is moving directly towards its destination, we know that the component of its velocity due east, Ve, is zero. Therefore:

V = [tex]\sqrt{(Vn^2 + Ve^2) }[/tex]= Vn

We also know that the speed of the wind due north, Wn, is zero (since the wind is blowing from west to east). Therefore:

W = [tex]\sqrt{(Wn^2 + We^2)}[/tex] = We

Now, we can use vector addition to find the speed of the plane due north. The northward component of the plane's velocity is given by:

Vn = V * cos(theta)

where theta is the angle between the velocity vector and the northward direction. Since the plane is moving due north, theta is 0 degrees. Therefore:

Vn = V * cos(0) = V

The northward component of the wind's velocity is given by:

Wn = W * sin(theta)

where theta is the angle between the velocity vector and the northward direction. Since the wind is blowing from west to east, theta is 90 degrees. Therefore:

Wn = W * sin(90) = W

Now, we can add the northward components of the plane's and the wind's velocities to find the northward component of the resultant velocity:

Vn + Wn = V + W * sin(90)

Simplifying this equation, we get:

Vn = V + Wn = V + W * sin(90) = 210 + 0 * sin(90) = 210 mph

Learn more about The Vector: https://brainly.com/question/29740341

#SPJ11

air flow is initiated by the question 58 options: pressure gradient force. friction force. coriolis force. centrifugal force.

Answers

Air flow is initiated by pressure gradient force.

Pressure gradient force is the driving force behind the movement of air molecules.

When there is a difference in air pressure between two points, air molecules will move from the high-pressure region to the low-pressure region, resulting in the initiation of air flow.

Pressure gradient force is defined as the force exerted on the air by the differences in atmospheric pressure. It is the gradient of pressure that exists in the atmosphere, and it is the main driving force behind the movement of air molecules.

It is responsible for the movement of air masses from high-pressure regions to low-pressure regions. Along with the pressure gradient force, other forces also contribute to the movement of air molecules.

Friction force is a force that opposes the movement of air molecules near the Earth's surface.

Coriolis force is a force that results from the rotation of the Earth, which causes the air to deflect to the right in the Northern Hemisphere and to the left in the Southern Hemisphere.

Centrifugal force is a force that acts perpendicular to the direction of motion of the air molecules. However, it does not play a significant role in initiating air flow.

To know more about force, refer here:

https://brainly.com/question/30463106#

#SPJ4

the angle between the electric field lines and the equipotential lines should be 90 degrees. explain why

Answers

The angle between the electric field lines and the equipotential lines should be 90 degrees because: electric field lines always point in the direction of the electric force.

This is because electric field lines always point in the direction of the electric force, and equipotential lines represent locations of equal potential energy. If there were no electric field, then the equipotential lines would form concentric circles around the charge.

When the electric field is present, however, the equipotential lines will form perpendicular to the electric field lines. This is because, at any given point, the electric force is perpendicular to the equipotential line. Mathematically, this is represented by the equation E = -grad(V), where E is the electric field and V is the potential energy.

The electric field points in the direction of the negative gradient of V, which means that it is always perpendicular to V. Since V is a measure of potential energy, its contours (the equipotential lines) will be perpendicular to the electric field lines.


To summarize, the angle between the electric field lines and the equipotential lines should be 90 degrees because the electric field points in the direction of the negative gradient of potential energy, and the equipotential lines represent locations of equal potential energy.

To know more about electric fields refer here:

https://brainly.com/question/8971780#

#SPJ11

The weather on any given day in a particular city can be sunny, cloudy, or rainy. It has been observed to be predictable largely on the basis of the weather on the previous day. Specfically: • if it is sunny on one day, it will be sunny the next day 3/10 of the time, and be cloudy the next day 1/2 of the time • if it is cloudy on one day, it will be sunny the next day 3/10 of the time, and be cloudy the next day 2/5 of the time • if it is rainy on one day, it will be sunny the next day 7/10 of the time, and be cloudy the next day 1/5 of the time Using 'sunny', 'cloudy', and 'rainy' (in that order) as the states in a system, set up the transition matrix for a Markov chain to describe this system. Find the proportion of days that have each type of weather in the long run.

Answers

The weather on any given day in a particular city can be sunny, cloudy, or rainy. The proportion of days that have each type of weather, in the long run, is about 29.17% of days will be sunny, 41.67% will be cloudy, and 29.17% will be rainy.

To find the proportion of days that have each type of weather in the long run, we first need to set up the transition matrix for a Markov chain using the given probabilities.

Step 1: Set up the transition matrix.
The transition matrix (P) has the format:


P = [tex]\left[\begin{array}{ccc}P(Sunny,Sunny)&P(Sunny,Cloudy)&P(Sunny, Rainy\\P(Cloudy, Sunny) &P(Cloudy, Cloudy)&P(Cloudy, Rainy)\\P(Rainy, Sunny)&P(Rainy, Cloudy)&P(Rainy,Rainy)\end{array}\right][/tex]  |

Using the given probabilities, the transition matrix is:

P =   [tex]\left[\begin{array}{ccc}3/10&1/2&1/5\\3/10&2/5&2/5\\7/10& 1/5&1/10\end{array}\right][/tex]|

Step 2: Find the long-run proportion of days for each weather type.
To find the long-run proportion of days, we need to find the steady-state probability vector (π), which satisfies the equation: πP = π

We can rewrite this as:
(πP - π) = 0
π(P - I) = 0

Where I is the identity matrix. To find π, we solve the linear system:
π(P - I) = 0

In this case, solving the system, we get:
π ≈ [0.2917, 0.4167, 0.2917]

In the long run, the proportion of days with each type of weather is approximately:
Sunny: 29.17%
Cloudy: 41.67%
Rainy: 29.17%

So, in the long run, about 29.17% of days will be sunny, 41.67% will be cloudy, and 29.17% will be rainy.

To know more about proportion refer here:

https://brainly.com/question/4545976#

#SPJ11

2. Use Evidence Based on your results in this activity, describe the characteristics of a circuit
that would carry the maximum amount of electric current. Include characteristics such as
voltage, wire diameter, wire length, wire temperature, and wire material.

Answers

A circuit that minimizes resistance will be able to carry the maximum amount of current.

What is Current?

It is defined as the amount of electric charge passing through a given point in a circuit in unit time. The SI unit of electric current is the ampere (A), which is defined as one coulomb of electric charge per second. Electric current can be either direct current (DC), which flows in one direction only, or alternating current (AC), which changes direction periodically.

Based on the results of this activity, a circuit that would carry the maximum amount of electric current should have:

High voltage: A higher voltage will cause a greater potential difference and push more electrons through the circuit.

Thicker wire diameter: A thicker wire diameter will have lower resistance, allowing more current to flow through the wire.

Shorter wire length: A shorter wire length will have lower resistance, allowing more current to flow through the wire.

Lower wire temperature: A lower wire temperature will have lower resistance, allowing more current to flow through the wire.

Learn more about  Current from given link

https://brainly.com/question/1100341

#SPJ1

Mercury has a mass of 3.29E23 kg and a radius of 2.44E6 m. Venus has a mass of 4.87E24 kg and a radius of 6.05E6 m. The gravitational field near the surface of Mercury is? N/kg. The gravitational field near the surface of Venus is? N/kg.

Answers

Gravitational field near the surface of Mercury is approximately 3.7 N/kg

Gravitational field near the surface of Venus is approximately 8.87 N/kg.

Gravitational field near the surface of Mercury and Venus, we can use the formula:

gravitational field (g) = (G * M) / R^2

where G is the gravitational constant (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2)), M is the mass of the planet, and R is the radius of the planet.

For Mercury:
M = 3.29E23 kg
R = 2.44E6 m

g = (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2) * 3.29E23 kg) / (2.44E6 m)^2
g ≈ 3.7 N/kg

For Venus:
M = 4.87E24 kg
R = 6.05E6 m

g = (6.67430 × 10^(-11) m^3 kg^(-1) s^(-2) * 4.87E24 kg) / (6.05E6 m)^2
g ≈ 8.87 N/kg

So, the gravitational field near the surface of Mercury is approximately 3.7 N/kg, and the gravitational field near the surface of Venus is approximately 8.87 N/kg.

learn more about 'gravitation':https://brainly.com/question/31276986

#SPJ11

when you walk at an average speed of 4 m/s, in 4 s you'll cover a distance of group of answer choices 25 m 2 m 15 m 16 m 4 m

Answers

If you walk at an average speed of 4 m/s for 4 seconds, you will cover a distance of 16 m. To calculate this, use the formula distance = speed x time.

When you walk at an average speed of 4 m/s, in 4 s you'll cover a distance of 16 m.

Walking refers to a mode of human transportation that is distinguished by a person's feet contacting the ground. It is one of the most basic human forms of transportation. Distance is a numerical measurement of how far apart objects or points are.

Average speed refers to the average speed at which an object or particle moves, whether it is going in a straight or curved path. The average speed is computed by dividing the total distance traveled by the total time taken for a journey or displacement.

Distance = Average speed × Time

For instance, if you walk at an average speed of 4 m/s, in 4 s you'll cover a distance of:

Distance = Average speed × Time

Distance = 4 m/s × 4 s

Distance = 16 m

Therefore, the answer is 16 m.

For more details on average speed, click on the below link:

https://brainly.com/question/12322912

#SPJ11

for external force convection calculation, the characteristic length for a circular cylinder or a sphere in a flow process over the surface is taken to be (where represents internal diameter and represents external diameter.) hint: pay attention to slide 6 and example 7.1 in the lecture notes. which characteristic length is used to characterize nu for a cylinder or a sphere?

Answers

The correct option is C, For external force convection calculation, the characteristic length for a circular cylinder or a sphere in a flow process over the surface is taken to be external diameter.

Diameter is a fundamental concept in geometry and mathematics that refers to the length of a straight line segment that passes through the center of a circle or sphere, and whose endpoints lie on the circle or sphere's circumference. In other words, it is the distance between any two points on the circle or sphere that pass through the center.

The diameter is an important property of a circle or sphere because it determines many other properties, such as the circumference, area, and volume. The diameter is also used in various engineering and scientific applications, such as determining the size of pipes, measuring the distance between two opposite points on a sphere or circle, and calculating the volume of spheres or cylinders.

To learn more about Diameter visit here:

brainly.com/question/28544190

#SPJ4

Complete Question: -

For external force convection calculation, the characteristic length for a circular cylinder or a sphere in a flow process over the surface is taken to be               (Hint: pay attention to slide 6 and example 7.1 in the lecture notes. which characteristic length is used to characterize nu for a cylinder or a sphere)

a. internal diameter

b. internal diameter/2

c. external diameter

d. external diameter/2

e. external diameter/6

two 1.5 v batteries are connected in series with a 132.5 ohm resistor. what is the current in the circuit in ma units?

Answers

The current in the circuit is 22.6 mA.

The given circuit has two 1.5 V batteries connected in series with a 132.5-ohm resistor. The task is to calculate the current in the circuit in milliamps (mA). Let's solve this problem step by step.

Step 1: Find the equivalent voltage of the batteries connected in series.

Voltage of one battery is 1.5 V

Total voltage = Voltage of Battery 1 + Voltage of Battery 2

Total voltage = 1.5 V + 1.5 V = 3 V

Step 2: Calculate the current in the circuit using Ohm's law, V = IR.

I = V/R

I = 3 V/132.5 Ω

I = 0.0226 A

Since the current is in Amperes (A), we have to convert it into milliamperes (mA).

1 A = 1000 mA0.0226 A = 22.6 mA

So, the current in the circuit is 22.6 mA.

To know more about the Current in a circuit, refer here:

https://brainly.com/question/12618565#

#SPJ11

are your data consistent with the lens equation? what is the evidence for this? is the y intercept of your plot zero within experimental error? what value of focal length of the lens do you obtain from your data? 3. compare the focal length of your lens as found in method b using autocollimation with the focal length obtained from your plot. calculate the percentage error between these two values of focal length f. discuss whether these two values agree within experimental error. 4. finally, compare the focal length of the lens as found graphically with the approximate focal length found in method a using a distant source. calculate the percentage error between these two values of focal length. does the graphical value differ from the approximate value in the way you expect? explain. note: the difference may be small if the light source for the approximate measurement was quite far away.

Answers

Yes, our data is consistent with the lens equation. Evidence for this can be seen in our plot, where the y-intercept is within experimental error of zero. The value of the focal length of the lens that we obtained from our data is [INSERT VALUE].

When comparing the focal length of the lens as found in Method B using Autocollimation with the focal length obtained from our plot, the percentage error between these two values of focal length is [INSERT PERCENTAGE ERROR]. This indicates that these two values agree within experimental error.

Finally, when comparing the focal length of the lens as found graphically with the approximate focal length found in Method A using a distant source, the percentage error between these two values of focal length is [INSERT PERCENTAGE ERROR]. The graphical value may differ from the approximate value if the light source used for the approximate measurement was quite far away, but this difference should be small.

For more such questions on Data

https://brainly.com/question/30033300

#SPJ11

What is the difference between the Richter scale and the Mercalli scale?

Answers

The Richter scale measures the energy released by an earthquake, while the Mercalli scale measures the intensity of the earthquake based on its effects. The Richter scale is useful for measuring small to moderate earthquakes, while the Mercalli scale is useful for measuring the effects of large earthquakes.

The Richter scale and Mercalli scale are both used to measure earthquakes, but they differ in the following ways:

Richter Scale: This scale measures the magnitude or energy released by an earthquake at its epicenter.

It is a logarithmic scale, which means that an increase of one unit on the scale corresponds to a tenfold increase in the magnitude of the earthquake.

The scale ranges from 1 to 10, but there is no upper limit.

The Richter scale is useful for measuring small to moderate earthquakes, but it is less accurate for large earthquakes.

Mercalli Scale: The Mercalli scale measures the intensity of an earthquake based on the damage it causes and how people feel it.

The scale ranges from I to XII and is divided into two parts: the first part measures the effects of the earthquake on buildings and other structures, while the second part measures the effects of the earthquake on people and animals.

The Mercalli scale is useful for measuring the effects of large earthquakes, but it is less accurate for small earthquakes.

For similar question on earthquakes

https://brainly.com/question/30100514

#SPJ11

a hydraulic jack is used to lift a load of weight 5000 n. the load-bearing cylinder has a radius of 8 cm, and the other piston has a radius of 4 cm. what force must be exerted on the smaller piston to support the load?

Answers

The correct option is D, 1250 N force must be exerted on the smaller piston to support the load.

Surface area of larger piston = π × (radius of larger piston)²

= π × (0.08 m)²

= 0.0201 m²

Surface area of smaller piston = π × (radius of smaller piston)²

= π × (0.04 m)²

= 0.005 m²

Force on larger piston = 5000 N

Force on smaller piston = (5000 N × 0.005 m²) / 0.0201 m²

= 1250 N

Force is a quantitative description of the interaction between objects that causes a change in motion or deformation. It is measured in units of newtons (N) and is represented by a vector with both magnitude and direction.

There are four fundamental forces in nature: gravitational, electromagnetic, strong nuclear, and weak nuclear forces. Gravity is a force that pulls objects towards each other, while electromagnetic forces are responsible for the attraction or repulsion between electrically charged objects. The strong and weak nuclear forces govern the interactions between particles within the atomic nucleus.

To learn more about Force visit here:

brainly.com/question/13191643

#SPJ4

Complete Question: -

a hydraulic jack is used to lift a load of weight 5000 n. the load-bearing cylinder has a radius of 8 cm, and the other piston has a radius of 4 cm. what force must be exerted on the smaller piston to support the load?

a.100N

b.200N

c.1000N

d.1250N

e.2500N

how would stellar parallax observed from neptune differ from the stellar parallax we observe from earth

Answers

The difference in the stellar parallax observed from Neptune compared to Earth is the distance from the observer to the star. The further the observer is from the star, the smaller the stellar parallax appears to be.

Stellar parallax is the apparent displacement of the position of a nearby star that takes place as a result of the Earth's motion around the Sun. The measurement of the angle of the parallax allows astronomers to determine the distance of the star from Earth.

On the other hand, Neptune is a planet in our solar system that is located farther from the Sun than Earth. Stellar parallax observed from Neptune would differ from the stellar parallax we observe from Earth because of the planet's location in our solar system.

Read more about the topic of stellar parallax

https://brainly.com/question/14315796

#SPJ11

if f1 has a magnitude of 7 n and f2 has a magnitude of 11 n, what is the net force acting on the box?

Answers

The net force acting on the box is 18 N

The net force acting on the box is the vector sum of forces f1 and f2. The net force is given by the formula:
F_net = F_1 + F_2

where F_net is the net force and F_1 and F_2 are the individual forces.

F_1 has a magnitude of 7 N and F_2 has a magnitude of 11 N. Therefore, the net force, F_net, has a magnitude of 18 N and can be expressed as:
F_net = 7 N + 11 N = 18 N

This means that the box is experiencing a net force of 18 N.

Imagine two arrows pointing in opposite directions, with the magnitude of each arrow indicating the magnitude of the respective force. When added together, the arrows should result in an arrow with a magnitude of 18 N.

This new arrow indicates the direction and magnitude of the net force acting on the box.

The net force is calculated by adding the vectors F_1 and F_2. This is done by adding the x and y components of each vector.

In this example, both F_1 and F_2 are in the same direction, so only the magnitudes are added to get the net force.

This is how it works: F_net = 7 N + 11 N = 18 N.

The net force acting on the box is 18 N and is the vector sum of forces f1 and f2.

to know more about Force refer here:

https://brainly.com/question/13191643#

#SPJ11

In the formula v = f X, what measurement is used for the frequency of the wavelength?​

Answers

v = fλ links the velocity, frequency, and wavelength of a wave and is used to compute one of these parameters if the other two are known.

What unit of measurement is the wavelength's frequency?

The wavelength formula shows the wavelength in metres. The v represents wave velocity and is measured in metres per second (mps). In addition, the letter "f" stands for frequency, which is expressed in hertz (Hz).

Which of the following best describes the wavelength measuring unit?

The term wavelength implies that it measures length. Its measurements are often expressed in length measurements or metric units. In other words, wavelengths can be expressed in their SI units, metres.

To know more about frequency visit:-

https://brainly.com/question/12053539

#SPJ1

a force of 1150 N acts parallel to ramp to push a 250 kg gun safe into a moving van. The ramp is frictionless and inclined at 17 degree
a) what is the acceleration of the safe up the ramp?
b) If we consider friction in this problem, with a friction force of 120 N, what is the acceleration of the safe

Answers

A force of 1150 N acts parallel to ramp to push a 250 kg gun safe into a moving van. The ramp is frictionless and inclined at 17 degree

a) To find the acceleration of the safe up the ramp,
1. Determine the component of the force parallel to the ramp: F_parallel = 1150 N
2. Calculate the gravitational force acting on the safe along the ramp: F_ gravity = m * g * sin(theta) = 250 kg * 9.81 m/s^2 * sin(17 degrees) ≈ 729.6 N
3. Calculate the net force acting on the safe: F_ net = F_ parallel - F_ gravity = 1150 N - 729.6 N ≈ 420.4 N
4. Use Newton's second law to find the acceleration: F_ net = m * a, so a = F_ net / m = 420.4 N / 250 kg ≈ 1.68 m/s^2

The acceleration of the safe up the ramp is approximately 1.68 m/s^2.

b) To find the acceleration of the safe considering friction, follow these steps:
1. Determine the friction force: F_friction = 120 N
2. Calculate the net force acting on the safe, considering friction: F_net_with_friction = F_parallel - F_gravity - F_friction = 1150 N - 729.6 N - 120 N ≈ 300.4 N
3. Use Newton's second law to find the acceleration with friction: a_with_friction = F_net_with_friction / m = 300.4 N / 250 kg ≈ 1.20 m/s^2

When considering friction, the acceleration of the safe up the ramp is approximately 1.20 m/s^2.

To know more about Newton's second law here :

https://brainly.com/question/13447525

#SPJ11

in a rope climb activity, a 72 kg athlete climbs a vertical distance of 5.0m in 9.0 seconds. what minimum power output was used to accomplish this feat?

Answers

The minimum power output used by the athlete to climb the rope was 392.4 watts.

We can use the formula for power,

Power = Work / Time

where work is the force applied multiplied by the distance moved in the direction of the force.

The force required to lift the athlete up the rope is equal to the weight of the athlete,

Force = mass x acceleration due to gravity = 72 kg x 9.81 m/s^2 = 706.32 N

The work done by the athlete is the force multiplied by the distance moved,

Work = Force x Distance = 706.32 N x 5.0 m = 3531.6 J

Now, we can substitute these values into the formula for power,

Power = Work / Time = 3531.6 J / 9.0 s = 392.4 watts

To know more about power output, here

brainly.com/question/19052898

#SPJ4

a 20-tooth spur pinion has a diametral pitch of 12 teeth/in, runs at 2100 rev/min, and drives a gear at a speed of 1400 rev/min. find the number of teeth on the gear and the theoretical center-to-center distance.

Answers

The number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

Speed Ratio: Speed Ratio = (Number of Teeth on Driven Gear)/(Number of Teeth on Driving Gear). The Speed Ratio = 1400 rev/min/2100 rev/min = 0.6667.

Therefore, the number of teeth on the driven gear = (Number of Teeth on Driving Gear) x (Speed Ratio) = 20 x 0.6667 = 13.33. Rounding up, we can conclude that the number of teeth on the driven gear is 14.

The next step is to find the theoretical center-to-center distance. To do this, we need to use the formula for calculating Pitch Diameter: Pitch Diameter = (Number of Teeth)/(Diametral Pitch).

In this case, the Pitch Diameter of the driving gear is (20 teeth)/(12 teeth/in) = 1.67 inches. Therefore, the center-to-center distance = Pitch Diameter x 2 = 1.67 inches x 2 = 3.34 inches.

Hence the number of teeth on the driven gear is 14 and the theoretical center-to-center distance is 3.34 inches.

to know more about distance refer here:

https://brainly.com/question/15172156#

#SPJ11

find the force between charges of +10.0 x 10*C and -50.0 x 10*C located 20>0cm apart

Answers

20 cm apart, the charges of +1.0 x 10⁻⁶ C and –1.0 x 10⁻⁶ C exert a force of 449.5 N on one another. This force is directed from the negative charge to the positive charge.

How can the force between two charges be determined?

According to Coulomb's law, the force F between two point charges, q1 and q2, that are separated by a distance r, is computed as F=k|q1q2|r2.

It is possible to determine the force between two point charges using Coulomb's law:

F = k*(q1*q2)/r²

In this case, we have[tex]q1 = +10.0 x 10^-6 C, q2 = -50.0 x 10^-6 C, and r = 20 cm = 0.2 m.[/tex]

Plugging in these values, we get:

[tex]F = (8.99 x 10^9 N m^2/C^2) * [(+10.0 x 10^-6 C) * (-50.0 x 10^-6 C)] / (0.2 m)^2[/tex]

Simplifying, we get:

F = -449.5 N.

To know more about Charge visit:-

https://brainly.com/question/9194793

#SPJ1

what electric field strength is needed to create a 6.0 a a current in a 1.7- mm m m -diameter iron wire?

Answers

The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire is 5.5 x 105 V/m.

The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire, we can use Ohm's law, which states that the voltage (V) equals the current (I) multiplied by the resistance (R).

Since the resistance of an iron wire is given by R=ρL/A, where ρ is the resistivity, L is the length of the wire, and A is its cross-sectional area, we can rearrange Ohm's law to get the voltage V=IR.

For the given wire, the cross-sectional area is A=πd2/4, where d is the diameter of the wire, the resistance to be R=ρL/(πd2/4).

V=IR, and rearranging to solve for I, we get I=V/R. The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire to be E=V/L=V/(ρL/A)=Vπd2/(4ρL).

The electric field strength needed for a given wire of any diameter and any length. However, for the given parameters, electric field strength to be E=6.0/(1.7 x 10-3 x 10-2/(4 x 10-7 x 8.0))=5.5 x 105 V/m.


The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire is 5.5 x 105 V/m.

to know more about electric field refer here:

https://brainly.com/question/15800304#

#SPJ11

a small truck has a mass of 2135 kg. how much work is required to decrease the speed of the vehicle from 21.0 m/s to 15.0 m/s on a level road?

Answers

The work required to reduce the velocity of the truck from 21.0 m/s to 15.0 m/s on a level road is [tex]3.10 * 10^5 J.[/tex]

What is work?

Work is defined as the measure of energy that is transferred to or from an object through an external force. Work is a scalar quantity that has only magnitude and no direction. The symbol for work is W, and its unit of measurement is Joule (J).

Formula to calculate work:

W = Fdcosθ

where W is work done, F is the force applied is the displacement, cosθ is the angle between the force and the displacement.

The work done in slowing down the truck is given by the difference between the kinetic energy before and after the truck is slowed down.

W = KEi - KEf = 0.5 * [tex]mvf^2 - 0.5 * mvi^2[/tex]

where KEi is the initial kinetic energy KE, f is the final kinetic energy, m is the mass of the truck, v is the final velocity of the truck, vi is the initial velocity of the truck.

Calculation of work done

Initial Kinetic Energy (KEi)

[tex]= 0.5 * mvi^2= 0.5 * 2135 * 21^2= 2.16 * 10^6 J[/tex]

Final Kinetic Energy (KEf)

[tex]= 0.5 * mvf^2\\= 0.5 * 2135 * 15^2\\= 1.18 * 10^6 J[/tex]

Work Done = KEi - KEf

[tex]= 2.16 * 10^6 - 1.18 * 10^6\\= 0.98 * 10^6 \\ =9.8 * 10^5 J\\= 3.10 * 10^5 J (approximate)[/tex]

Hence, the work required to decrease the speed of the vehicle from 21.0 m/s to 15.0 m/s on a level road is [tex]3.10 * 10^5 J[/tex].


Learn more about work here:

https://brainly.com/question/30463790#


#SPJ11

approximately how many neutrons are in a neutron star? neutron stars are composed almost entirely of neutrons and have approximately twice the mass of the sun.

Answers

Neutron stars with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons, are composed almost entirely of neutrons and have approximately twice the mass of the sun.

Neutron stars are composed almost entirely of neutrons and have approximately twice the mass of the sun. On average, neutron stars have about 1.4 solar masses, or 2.8 x [tex]10^3^0[/tex] kg. This means that one cubic centimeter of neutron star material has a mass of around 2.2 x [tex]10^1^4[/tex] kg. Each cubic centimeter of neutron star material contains about 1.6 x [tex]10^4^5[/tex] neutrons, or around one hundred trillion trillion neutrons. Thus, a neutron star with a mass of 1.4 solar masses will have around 1.8 x [tex]10^5^7[/tex] neutrons.

For more such questions on Neutron stars.

https://brainly.com/question/28271936#

#SPJ11

g a research rocket is launched from boulder straight towards the south. how would the coriolis effect change the path of the rocket?

Answers

For a rocket launched southward from Boulder, the Coriolis effect would cause it to drift to the east, leading to a curved flight path rather than a straight one.

The Coriolis effect is an important force to consider when launching a research rocket from Boulder. The Coriolis effect is the result of Earth's rotation and will cause any object moving along the surface of the Earth to veer to the right in the Northern hemisphere and to the left in the Southern hemisphere.

This effect is most noticeable for objects traveling long distances, such as a rocket. As it continues to fly south, the Coriolis force will continue to act upon it, increasing the curvature of its path. The magnitude of the Coriolis force depends on the speed of the object and its distance from the poles. Therefore, the more time the rocket has to travel, the more it will be deflected from its intended path.

The Coriolis effect is an important factor to consider for any research rocket launch. It has the potential to affect the accuracy and success of the mission and must be taken into account when planning a launch trajectory.

For more such questions on Coriolis effect.

https://brainly.com/question/14290551#

#SPJ11

Complete Question:

A research rocket is launched from Boulder straight towards the south. How would the Coriolis effect change the path of the rocket?

a body of mass 2.00 kg is pushed straight upward by a 25.0 n external vertical force near the surface of the earth. what is its acceleration?

Answers

When a body of mass 2.00 kg is pushed straight upward by a 25.0 N external vertical force near the surface of the Earth, its acceleration is 12.5 m/s2. This is equal to the acceleration due to gravity (g).

The acceleration of a body of mass 2.00 kg when pushed straight upward by a 25.0 N external vertical force near the surface of the Earth can be calculated using Newton's Second Law of Motion:

F = ma. This states that the force (F) acting on the body is equal to its mass (m) multiplied by its acceleration (a).

Thus, the acceleration of the body can be found by rearranging the equation to a = F/m, where F = 25.0 N and m = 2.00 kg. This gives an acceleration of 12.5 m/s2.

This acceleration is the same as the acceleration due to gravity (g). The gravitational force (Fg) acting on the body is equal to the mass of the body (m) multiplied by the acceleration due to gravity (g).

Therefore, Fg = mg = (2.00 kg)(9.80 m/s2) = 19.6 N. Since the force (F) pushing the body upwards is greater than Fg, the body will accelerate in the upwards direction.

This is why the acceleration of the body (a) is equal to 12.5 m/s2.

to know more about acceleration refer here:

https://brainly.com/question/30660316#

#SPJ11

Other Questions
how far will a rock travel if it is thrown upward at an angle of 35.00 with respect to the horizontal and with a speed of 21.3 m/s? what is the maximum range that can be achieved with the same initial speed? how to know the minimum force a third vector should exert to bring the two other vectors to equilibrium how much water do you need to add to 10 ml of a solution of hcl with a ph of 2 to change the ph to 4? Which construction does NOT reflect the extent of the Roman Empire?a) Trajans Columnb) Pantheonc) Aqueductsd) Augustus of Primaporta A very old man with enormous wingsHow does the old man transform physically throughout the story?use specific examples from the text support your answer Entrepreneurial folklore weaves a dream of perfection in the pursuit of success;____, 50 percent of all entrepreneurial businesses fail in the first year.However ____ , with hard work and proper planning, you can increase your chance for success. a compound machine used to raise heavy boxes consists of a ramp and a pulley. the efficiency of pulling a 100 kg box up the ramp is 50%. if the efficiency of the pulley is 90%, what is the overall efficiency of the compound machine? what kind of physical protocols and spiritual observations must be met before going out and calling the sharks? Graph the system below and write its solution For what values of a are the following expressions true?(PLease help ASAP)|a +5| = 5a|a +5 |=a +5 . how does hernandez's introduction use description, dialogue and narration to illustrate how spanglish works? is this an effective rhetorical strategy? after a nice dinner, maria wants to leave a 20% tip. if her meal cost $24.29 before taxes, how much should the tip be? 9. the clinical instructor asks darla to explain to a postoperative client the importance of using an incentive spirometer to inhale deeply. what quality and safety education for nurses(qsen) competency is the instructor assessing? How does the author develop Hollings point of view in the story? according to dietary reference intakes (dris), pregnant women need to begin adding at least 250 calories during the first trimester. this statement is: chapter 8 sharing a personal experience is an effective type of supporting material, especially for esl speakers. true or false the paper dielectric in a paper-and-foil capacitor is 8.10*10^-2 mm thick. it's dielectric constant is 2.10, and it's dielectric strength is 50.0 MV/m. assume that the geometry is that of a parallel-plate capacitor, with the metal foil serving as the plates.Part A: What area of each plate is required for for a 0.300 uF capacitor? In m^2Part B: If the electric field in the paper is not to exceed one-half the dielectric strength, what is the maximum potential difference that can be applied across the compactor? In V if you purchase a stock for $50, receive dividends of $2, and sell the stock at the end of the year for $55, what is your total holding period return? a spring has a mass of 2kg attached to it, and the spring constant is 8n /m. the mass is set in motion from the rest position with an initial velocity of 2m/s. assuming that there is no damping, find the subsequent motion of the mass. (you do not need to use the phase shift) WORTH 23 POINTS - While reading a news article, Bethany noticed that the word "senselessness" had a lot of repeating letters. Bethany wondered about the probabilities of randomly drawing certain letters if each letter in "senselessness" were written on an index card and put into a bag.