Ammonium acetate is a chemical compound with the formula CH3COONH4, and it is an ionic salt. It is colorless, crystal-like, and readily soluble in water. Acetic acid and ammonia are the two primary components of ammonium acetate. Ammonium acetate is commonly used in the production of various chemicals, such as dyes, insecticides, herbicides, and various other chemicals.
Thin-layer chromatography (TLC) is a common method for separating compounds in a mixture based on their polarity. The solvent used in TLC should be of low polarity, which would not dissolve the silica gel on which the sample is applied. Additionally, the solvent should be polar enough to elute the compound with the lowest polarity out of the sample.
Ammonium acetate is used in the solvent mixture for a TLC analysis in week 2 because it enhances the separation of polar compounds in the mixture. It is frequently used in mass spectrometry as a volatile buffer to improve ionization efficiency. Ammonium acetate buffers can also be utilized in chromatography to improve the separation of peptides and proteins.
Ammonium acetate is utilized to enhance the separation of polar compounds in TLC analysis because it is an ionic salt, which means it is polar. As a result, it dissolves polar compounds more effectively, allowing them to migrate across the TLC plate more efficiently. It also aids in the formation of strong hydrogen bonds between polar solutes, allowing them to be separated more effectively.
In conclusion, the usage of ammonium acetate in the solvent mixture for the TLC analysis in week 2 is due to its polar nature. It improves the separation of polar compounds in the mixture and is a common additive used to improve ionization efficiency in mass spectrometry.
To know more about TLC analysis click here:
https://brainly.com/question/24082910
#SPJ11
what is the concentration of fecl3in a solution prepared by dissolving20.0 g of fecl3in enoughwater to make 275 ml of solution?
The concentration of FeCl₃ is 0.447M.
To calculate this, we must first determine the number of moles of FeCl₃ in the solution. The molar mass of FeCl₃ is 162.2 g/mol, so the number of moles of FeCl₃ is (given weight)/(Molar mass) =0.123 moles.
Next, we need to calculate the total volume of the solution, which is given= 275 mL.
To calculate the concentration, we divide the number of moles of FeCl₃ (0.123 moles) by the total volume of the solution (275 mL). We can then convert mL to L by dividing by 1000, so the total volume of the solution is 0.275 L.
This gives us a concentration of:
Concentration= (No. of moles)/(Volume in L)
=(0.123 moles/0.275 L)
=0.447M
Therefore, The concentration of FeCl₃ in a solution prepared by dissolving 20.0 g of FeCl3 in enough water to make 275 mL of solution is 0.447M.
To know more about FeCl₃, refer here:
https://brainly.com/question/28299457#
#SPJ11
select a mineral, rock, or gemstone from the united state and explain why you selected it. discuss how the mineral, rock, or gemstone you selected is used in everyday life, and the processes by which they formed.
Answer: I have selected the gemstone turquoise from the United States. Turquoise is a semi-precious gemstone composed of copper aluminum phosphate. It is found in the deserts of Nevada, Arizona, Colorado, and New Mexico. Turquoise has a long history of use, with some pieces found in Ancient Egyptian tombs and Native American jewelry. Turquoise is still used today for making jewelry, figurines, and inlays for furniture. It is also often used to decorate clothes and other items.
Turquoise is created through the process of sedimentary precipitation, which involves the accumulation of minerals in slow-moving water. This process takes thousands of years, and is further shaped by the elements, such as air and water, which break down the mineral and change its color. It can also be artificially altered to improve its color.
In everyday life, turquoise is primarily used for jewelry, but it is also thought to possess healing properties. In some cultures, turquoise is believed to bring good luck and is used to ward off evil spirits. Turquoise has been a popular choice for making jewelry and decorative objects since ancient times. It is a beautiful, vibrant gemstone with a wide range of colors and patterns, which makes it a highly sought after material.
Learn more about minerals here:
https://brainly.com/question/18078524#
#SPJ11
The diagram shows the cycling of matter in the interior of Earth.
Which statement correctly explains the cycling of matter in the interior of Earth?
Responses
The heat from Earth’s core causes material in the area under the crust to become less dense and rise, while more dense material sinks.
The heat from Earth’s core causes material in the area under the crust to become less dense and rise, while more dense material sinks.
The heat from Earth’s core causes material in the area under the crust to become more dense and rise, while less dense material sinks.
The heat from Earth’s core causes material in the area under the crust to become more dense and rise, while less dense material sinks.
The heat from Earth’s core causes material in the area under the crust to become less dense and sink, while more dense material rises.
The heat from Earth’s core causes material in the area under the crust to become less dense and sink, while more dense material rises.
The heat from Earth’s core causes material in the area under the crust to become more dense and sink, while less dense material rises.
The heat from Earth’s core causes material in the area under the crust to become more dense and sink, while less dense material rises.
Answer:
Explanation:
I think 'The heat from Earth's core causes material in the area under the crust to become denser and rinse, while less dense material sinks.
write an equation for each acid or base showing its ionization in water, and write the equilibrium constant expression for the weak acid or base
The equation for the ionization of a weak acid in water is HA + H₂O ⇌ H₃O⁺ + A⁻, and the equilibrium constant expression for this reaction is K = [H₃O⁺ ][A⁻]/[HA].
The ionization of a weak base in water is B + H₂O ⇌ OH⁻ + BH+, and the equilibrium constant expression for this reaction is K = [OH⁻][BH⁺]/[B].
Weak acids and bases partially dissociate into their ions in aqueous solutions. For a weak acid, HA, the equilibrium expression for its ionization is HA + H₂O ⇌ H₃O⁺ + A⁻, and the corresponding equilibrium constant expression is K = [ H₃O⁺ ][A-]/[HA].
The same process happens with a weak base, B, where the equilibrium expression is B + H₂O ⇌ OH⁻ + BH⁺, and the corresponding equilibrium constant expression is K = [OH⁻][BH⁺]/[B]. Thus, the equations for the ionization of both weak acids and bases and the corresponding equilibrium constant expressions can be
To know more about equilibrium constant click on below link:
https://brainly.com/question/15118952#
#SPJ11
why the net ionic equation for the neutraliza-
tion reaction of any strong acid with any strong base
is always the same.
Answer:
The net ionic equation for the neutralization reaction of any strong acid with any strong base is always the same because both the strong acid and the strong base completely dissociate in water into their respective ions, and the reaction between them always results in the formation of water and a salt.
For example, when hydrochloric acid (HCl) is neutralized by sodium hydroxide (NaOH), the following reaction occurs:
HCl (aq) + NaOH (aq) → NaCl (aq) + H2O (l)
In this reaction, both HCl and NaOH completely dissociate into their respective ions in water:
HCl (aq) → H+ (aq) + Cl- (aq)
NaOH (aq) → Na+ (aq) + OH- (aq)
The net ionic equation for this reaction is:
H+ (aq) + OH- (aq) → H2O (l)
As you can see, the net ionic equation is the same for any strong acid and any strong base, since the reaction always involves the combination of H+ and OH- ions to form water. The identity of the cations and anions in the salt formed will vary depending on the specific acid and base used, but the overall reaction and the resulting net ionic equation will always be the same.
Mark me as brainliest!
For the incomplete Reaction (below), the mass of the missing product should be...
) -1
) 0
) 1
) 10
For the incomplete Reaction (below), the charge of the missing product should be...
) -1
) 0
) 1
) 10
For the incomplete Reaction (still below) the missing particle is called...
- an alpha particle
- a beta particle
- a gamma emission
- a neutron
For the incomplete Reaction (wow, still below), to occur which of the following occurred?
- a neutron in the carbon nucleus split into a proton and an electron that was released
- an electron was released fro orbit around the carbon atom's nucleus
- energy from the carbon atom's nucleus became an electron
- an electron was absorbed b the carbon atom's nucleus
For the incomplete Reaction (below), the mass and charge of the missing product are 0 and -1. The missing product is a beta particle where a neutron in the carbon nucleus split into a proton and an electron that was released.
What is beta particle emission?Beta particle emission, also known as beta decay, is a type of radioactive decay in which a beta particle is emitted from the nucleus of an atom.
A beta particle is a high-energy, high-speed electron or positron that is released from the nucleus as a result of the transformation of a neutron into a proton or a proton into a neutron.
Learn more about beta particles at: https://brainly.com/question/24312947
#SPJ1
why is molality used as a concentration scale in this experiment and not the more common concentration scale of molarity?
Molality is used as a concentration scale in this experiment instead of molarity because it is not affected by temperature changes.
Molarity is a measure of the number of moles of a substance dissolved in a liter of solution, and its value can vary with temperature changes. On the other hand, molality is a measure of the number of moles of solute per kilogram of solvent and is not affected by temperature changes. This makes it a better choice of concentration scale in experiments where temperature fluctuations could otherwise affect the accuracy of results.
In this experiment, molality is used to ensure accurate results. By using molality instead of molarity, the experimenter is able to account for temperature changes that could affect the outcome of the experiment, resulting in a more reliable and accurate set of results.
Thus, Molality is used as a concentration scale in this experiment instead of molarity to avoid temperature-related discrepancies.
To know more about Molality, refer here:
https://brainly.com/question/26921570#
#SPJ11
which two gases are primarily responsible for the greenhouse effect because of their ability to absorb infrared energy?
The two primary gases responsible for the
greenhouse effect
are carbon dioxide (CO2) and water vapor (H2O). They absorb infrared energy, which is a type of energy that is emitted from the Earth's surface, and trap it in the atmosphere.
This energy can't escape, which causes the atmosphere to warm up, resulting in the greenhouse effect.
The greenhouse effect is a natural process that helps to keep the Earth's temperature relatively stable, which is important for life.
The amount of CO2 and H2O in the atmosphere are regulated by natural processes, such as respiration and
photosynthesis
,
but human activities, such as burning fossil fuels and deforestation, have caused these levels to increase significantly over the past few decades.
This has resulted in a further increase in the temperature of the atmosphere, leading to climate change.
CO2 absorbs more infrared energy than other gases, but H2O also plays an important role in the greenhouse effect.
H2O exists in the atmosphere in both vapor and liquid forms, and is able to absorb and trap heat energy more effectively than CO2.
H2O also has the ability to reflect incoming sunlight, which further helps to keep the temperature of the atmosphere warm.
CO2 and H2O are the two primary gases responsible for the greenhouse effect because of their ability to absorb infrared energy and trap heat in the atmosphere.
These two gases are essential for regulating the temperature of the Earth and maintaining the climate.
Human activities have caused their levels to increase, resulting in a further increase in the temperature of the atmosphere and leading to climate change.
to know more about
greenhouse effect
refer here:
https://brainly.com/question/13706708#
#SPJ11
you have been called to the site of an overturned railroad tank car leaking potassium hydroxide. your task is to determine the corrosivity of the spill. the best monitoring equipment for the job is a:
The best monitoring equipment for determining the corrosivity of a potassium hydroxide spill is a pH meter.
A pH meter is a device that measures the acidity or alkalinity of a solution and provides a numerical value from 0 to 14. A pH value of 7 is neutral, while a pH below 7 is acidic and a pH above 7 is basic (alkaline).
Potassium hydroxide is a strong alkali with a pH value of approximately 13. This means it can corrode metals, concrete, and other materials it comes in contact with.
By measuring the pH of the spill, we can determine how corrosive it is and take the necessary steps to mitigate the corrosive effects. It is important to note that corrosion is not the same as toxicity.
Corrosion can cause serious damage, but the effects can often be reversed with proper mitigation and cleaning.
In order to measure the pH of a potassium hydroxide spill, it is important to use a pH meter with a temperature probe. This is because the pH of a solution can vary with temperature.
The pH meter should also be calibrated correctly before use, as incorrect readings can lead to incorrect conclusions.
After the pH meter is in place, readings can be taken of the spill and compared to a baseline reading from an uncontaminated sample in order to determine the level of corrosivity of the spill.
Appropriate actions can then be taken to mitigate the corrosive effects.
to know more about corrosivity refer here:
https://brainly.com/question/30057568#
#SPJ11
do how much salt do you add to a gallon of wateres how much salt does it take to purify a boiling pot of water salt purify water?
When using salt to purify water, the general recommendation is to add 1/8 to 1/4 teaspoon of salt per gallon of water. Salt is used in the water purification process because it can kill or inhibit the growth of harmful bacteria and other microorganisms that can cause diseases and illnesses.
Here are the steps to purify a boiling pot of water with salt:
1. Boil the water: Bring the water to a rolling boil for at least one minute.
2. Add salt: Once the water has boiled, add 1/8 to 1/4 teaspoon of salt per gallon of water.
3. Stir: Stir the water until the salt has dissolved.
4. Wait: Let the water sit for at least 30 minutes. During this time, the salt will kill or inhibit the growth of harmful bacteria and other microorganisms.
5. Taste: After the 30 minutes have passed, taste the water to see if it has a slightly salty taste. If it does, the water is safe to drink. If not, add more salt and repeat the process.
For more question on water click on
https://brainly.com/question/25326161
#SPJ11
A 100 milliliter sample of 0.100-molar NH4Cl solution was added to 80 milliliters of a 0.200-molar solution of NH3. The value of Kb for ammonia is 1.79 x 10^-5.
- What is the pH of the solution
- Some NaOH is added to the solution but the pH barely changes. write the reaction that explains this
- What is the pH of a solution with equal amounts of NH4Cl and NH3?
The pH of the solution is 9.95.
The reaction that explains this is given as NH4+ + OH- → NH3 + H2O
The pH of a solution with equal amounts of NH4Cl and NH3 is 12.21.
Determining the pH of the solutionTo solve this problem, we need to first write out the balanced chemical equation for the reaction between NH4Cl and NH3:
NH4Cl + NH3 ⇌ NH4+ + NH2Cl
Next, we need to write out the equilibrium expression:
Kb = [NH4+][OH-]/[NH3]
Since we are given the concentration of NH4Cl and NH3, we can use the initial concentrations to calculate the equilibrium concentrations of NH4+, NH2Cl, and NH3:
[NH4+] = 0.1 M × (0.1 L / 0.18 L) = 0.056 M
[NH2Cl] = 0.056 M
[NH3] = 0.2 M × (0.08 L / 0.18 L) = 0.089 M
Using the equilibrium expression and the value of Kb, we can solve for the concentration of hydroxide ions:
Kb = [NH4+][OH-]/[NH3]
1.79 × 10^-5 = (0.056 M)(x) / (0.089 M)
x = 1.13 × 10^-5 M
Finally, we can use the concentration of hydroxide ions to calculate the pH of the solution:
pH = 14 - pOH = 14 - (-log10(1.13 × 10^-5)) = 9.95
Therefore, the pH of the solution is 9.95.
If some NaOH is added to the solution but the pH barely changes, it means that the added NaOH is being neutralized by the NH4+ ions in the solution, forming more NH3 and water:
NH4+ + OH- → NH3 + H2O
This reaction helps to buffer the pH of the solution.
To calculate the pH of a solution with equal amounts of NH4Cl and NH3, we can use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
where A- is the conjugate base of the acid, NH4+, and HA is the acid, NH3.
The pKa of NH4+ is given by:
pKa = pKw - pKb = 14 - 1.79 = 12.21
At the halfway point, the concentration of NH4+ and NH3 are equal:
[NH4+] = [NH3]
Substituting these values into the Henderson-Hasselbalch equation, we get:
pH = 12.21 + log(1) = 12.21
Therefore, the pH of a solution with equal amounts of NH4Cl and NH3 is 12.21.
Learn more about pH values here https://brainly.com/question/172153
#SPJ1
at a particular temperature, the solubility of no in water is 0.090 m when the partial pressure is 0.80 atm. what partial pressure (in atm) of no would give a solubility of 0.060 m?
Solubility: The maximum amount of solute that can be dissolved in a solvent at a given temperature and pressure is called solubility.
Partial Pressure: The pressure that a gas exerts when it is present in a mixture of gases is called partial pressure.
The given solubility of NO in water is 0.090 m and the partial pressure is 0.80 atm. We need to find the partial pressure required for the solubility of NO to be 0.060 m.
Hence, let's find the relationship between solubility and partial pressure.
The relationship between solubility and partial pressure can be given as, Henry's Law:
S = KP
Where, S is the solubility of the gas in solution,
P is the partial pressure of the gas above the solution, and
K is Henry's Law constant.
Let's apply the given values to Henry's Law to find the value of
K.0.090 m = K (0.80 atm)
K = 0.090 m / 0.80 atm
K = 0.1125 m/atm
Now, let's find the partial pressure required for the solubility of NO to be 0.060 m using Henry's Law.
0.060 m = (0.1125 m/atm) P
So, the partial pressure required for the solubility of NO to be 0.060 m is 0.53 atm.
Learn more about solubility: https://brainly.com/question/9098308
#SPJ11
if 6.55 g 6.55 g of cuno3 cuno 3 is dissolved in water to make a 0.490 m 0.490 m solution, what is the volume of the solution in milliliters?
The amount of a substance in a specific volume of solution is known as its molarity (M). The number of moles of a solute per liter of a solution is known as molarity. The volume of the solution in milliliters is 69.3 mL.
Since most reactions take place in solutions, it's critical to comprehend how the substance's concentration is expressed in a solution. There are numerous ways to express how many chemicals are in a solution.
The letter M stands for molarity, one of the most often used units of concentration. The number of moles of solute contained in 1 liter of solution is how it is defined.
M = number of moles/volume in L
number of moles = Mass / Molar mass
Molar mass of Cu(NO₃)₂ = 187.55 g/mol
n = 6.55 / 187.55
n = 0.034 mol
0.490 = 0.034 / V
V = 0.0693 L
1 L = 1000 mL
0.0693 L = 69.3 mL
To know more about molarity, visit;
https://brainly.com/question/16587536
#SPJ12
why is the hybridization model necessary to explain the bonding in a molecule such as ch4? select all that apply.
It helps explain why there are 4 equivalent C-H bonds in CH4,It allows for a better representation of the arrangement of electrons in the molecule, and It helps explain why the dipole moment of the molecule is zero.
What is hybridization?Hybridization is the process of combining two or more distinct entities to create a new, unique entity that has a combination of the characteristics of the original entities. It can be used to describe a wide range of phenomena, ranging from the breeding of plants and animals to the intermixing of different cultures.
In biology, hybridization is the process of combining the genetic material of two different species to create a hybrid organism.
Learn more about hybridization here:
https://brainly.com/question/22765530
#SPJ1
the radius of a single atom of a generic element x is 123 picometers (pm) and a crystal of x has a unit cell that is body-centered cubic. calculate the volume of the unit cell.
The radius of a single atom of a generic element x is 123 picometers (pm) and a crystal of x has a unit cell that is body-centered cubic. So, the volume of the unit cell is 11.5482 x 10⁻²⁴ cm³.
Given,
The radius of a single atom of a generic element x is 123 picometers (pm) and a crystal of x has a unit cell that is body-centered cubic.
Body-Centered Cubic (BCC):
In a Body-Centered Cubic unit cell, each corner of the cube has a corner atom, and there is an additional atom in the center of the cube. The atom that is centered on the unit cell is surrounded by eight neighboring atoms, each of which is located at a distance of
4R/√3,
where R is the radius of the atom.
The volume of the unit cell = (4 * radius of the atom)^3/3
For BCC, volume of the unit cell is
(4 * radius of the atom)^3/3
= (4 * 123 pm)^3/3
= 11.5482 x 10⁻²⁴ cm³
The volume of the unit cell is 11.5482 x 10⁻²⁴ cm³.
For more such questions on volume , Visit:
https://brainly.com/question/29493123
#SPJ11
What is the value of the gas constant, R, in units of L atm/mol K? Report the value with at least three significant figures.
The value of the gas constant, R, in units of L atm/mol K is 0.0821 L atm/mol K.
What is the gas constant, R?The ideal gas law is described by the ideal gas equation,
PV = nRT,
which expresses the relationship between pressure, volume, temperature, and the number of moles of gas.
The gas constant, R, is a constant that relates these variables for a given quantity of an ideal gas at constant pressure and volume. Its value depends on the units used to express pressure, volume, temperature, and the number of moles of gas.
For the most common units, R has a value of 0.0821 L atm/mol K. This is equivalent to 8.31 J/mol K or 1.99 cal/mol K. The value of R is often used in solving problems involving the ideal gas law, such as determining the pressure, volume, or temperature of a gas sample under different conditions.
To learn more about gas refer: https://brainly.com/question/30859506
#SPJ11
a mixture of two gases with a total pressure of 2.00 atm contains 0.70 atm of gas a. what is the partial pressure of gas b in atm? 1 . 3 0
The partial pressure of gas B in a mixture of two gases can be found by subtracting the partial pressure of gas A from the total pressure of the mixture. In this case, the partial pressure of gas B is 1.30 atm.
To find partial pressure of gas B in the mixture of two gases : Partial pressure of gas B = Total pressure - Partial pressure of gas A
Given that the total pressure of the mixture is 2.00 atm and the partial pressure of gas A is 0.70 atm: Partial pressure B = 2.00 atm - 0.70 atm
Partial pressure of gas B = 1.30 atm.
Therefore, the partial pressure of gas B in the mixture is 1.30 atm.
To know more about partial pressure , here
brainly.com/question/13199169
#SPJ4
what will be the ph of a buffer solution prepared from 0.20 mol nh3, 0.40 mol nh4no3, and just enough water to give 1.00 l of solution?
The pH of the buffer solution is approximately 8.95.
To find the pH of the buffer solution, we'll use the Henderson-Hasselbalch equation:
pH = pKa + log ([A-]/[HA])
Here, [A-] is the concentration of NH3 (base), and [HA] is the concentration of NH4+ (conjugate acid). First, we need to find the pKa of NH4+. The pKa is the negative logarithm of the Ka (acid dissociation constant) value. For NH4+, the Ka value is 5.56 x 10^-10.
Step 1: Find pKa
pKa = -log(Ka) = -log(5.56 x 10^-10) = 9.25
Step 2: Find the concentration of NH3 and NH4+
[NH3] = 0.20 mol / 1.00 L = 0.20 M
[NH4+] = 0.40 mol / 1.00 L = 0.40 M
Step 3: Use the Henderson-Hasselbalch equation
pH = 9.25 + log(0.20/0.40) = 9.25 - 0.301 = 8.949
For more question on buffer solution click on
https://brainly.com/question/27371101
#SPJ11
what is the formula for the ionic compound formed by calcium and selenium? group of answer choices case case2 case3 ca2se ca3se
Answer: CaSe
Explanation:
Step 1: Ca has a +2 charge as a cation. Se has a -2 charge as an anion.
Ca²⁺ Se²⁻
Step 2: Use the "swap and drop" method. Swap the numbers on each ion and then drop them as subscripts. Omit the + and -.
Ca₂Se₂
Step 3: When the subscripts are the same, you can omit them and write the answer as CaSe.
The correct answer is option a) CaSe.
Ionic compounds are formed when a metal and a non-metal react.
In this case, calcium is a metal and selenium is a non-metal. This reaction forms a cation (positively charged ion) of calcium and an anion (negatively charged ion) of selenium.
The formula for the compound is the combination of the symbols of the two elements with the charges balanced. Since calcium is a +2 cation and selenium is a -2 anion, the compound's formula is CaSe.
Therefore, the formula for the ionic compound formed by calcium and selenium is CaSe.
To know more about calcium, refer here:
https://brainly.com/question/4023397#
#SPJ11
if 626 ml of a 0.110m lead ii nitrate soloution is reacted with 429 ml of a 3.4 m potassium iodide soloution how many grams of percipitate can be produced
20,908.6 g of precipitate were generated.
Lead (II) nitrate and Potassium iodide react to form Lead (II) iodide and Potassium nitrate.For this reaction, the chemical equation is balanced as follows:
[tex]2 Pb(NO_3)_2 + 2 KI \rightarrow 2 PbI_2 + 2 KNO_3[/tex]
To calculate the amount of precipitate produced, we first need to calculate the amount of moles of Lead (II) nitrate and Potassium iodide.
Amount of Lead (II) nitrate = 626 mL x (0.110 mol/L) = 68.86 mol
Amount of Potassium iodide = 429 mL x (3.4 mol/L) = 1458.6 mol
Since the reaction has a 2:2 mole ratio, the amount of moles of Lead (II) iodide produced is 68.86 mol.
Now, we can calculate the mass of the precipitate produced.
Mass of precipitate = 68.86 mol x (303.4 g/mol) = 20,908.6 g
Therefore, the amount of precipitate produced is 20,908.6 g.
learn more about precipitate Refer:brainly.com/question/30904755
#SPJ1
what is the percent yield if 578 g of h3po4 are produced when 10.0 moles of water react with an excess of p4o10?
The percent yield of H₃PO₄ when 10.0 moles of water react with an excess of P₄O₁₀ is 88.4%.
The balanced chemical equation is:
P₄O₁₀ + 6H₂O → 4H₃PO₄
We can find the theoretical yield of H₃PO₄ by using stoichiometry, which is the relationship between the number of moles of the reactants and products in a chemical reaction.
6.0 mol of H₂O reacts with P₄O₁₀ to give 4 moles of H₃PO₄ according to the balanced chemical equation.
Therefore, the number of moles of H₃PO₄ formed will be:
10.0 mol of H₂O x (4 mol of H₃PO₄ / 6 mol of H2O) = 6.67 mol of H₃PO₄
Now we can find the theoretical yield of H₃PO₄ using its molar mass, which is 98.0 g/mol.
Theoretical yield = 6.67 mol of H₃PO₄ x 98.0 g/mol = 653.6 g of H₃PO₄
The actual yield of H₃PO₄ formed in the reaction is given as 578 g.
Percent yield = actual yield / theoretical yield x 100%
Percent yield = 578 g / 653.6 g x 100% = 88.4%
Therefore, the percent yield will be lower than the expected value of 100%. It will be 88.4%.
To know more about percent yield, refer here:
https://brainly.com/question/2506978#
#SPJ11
given that burning a 1 gram carbohydrate sample raised the temperature of the 500 gram water bath by 8oc, calculate how much heat energy was released by the carbohydrate sample.
The burning of 1 gram carbohydrate release 16,736 J of heat energy.
Burning a 1 gram carbohydrate sample raised the temperature of the 500 gram water bath by 8°C, to calculate how much heat energy was released by the carbohydrate sample, we can use the specific heat capacity of water which is 4.18 J/g°C.
The heat energy released by the carbohydrate sample can be calculated using the following equation:
Heat energy (J) = mass of water (g) × specific heat capacity of water × ΔTHeat energy
In this case, the calculation is as follows:
Heat energy (J) = 500 g x 8°C x 4.184 = 16,736 J
Therefore, burning a 1 gram carbohydrate sample raised the temperature of the 500 gram water bath by 8°C and released 16,736 J of heat energy.
Learn more about heat energy: https://brainly.com/question/878982
#SPJ11
A scientist collects data that shows the surface around a volcano is swelling a few centimeters. Which conclusion is the scientist most likely to make based on this data?
A. Magma is becoming more active underneath the volcano, which could lead to an eventual eruption. B. A volcanic eruption cannot occur within the next 30 days. C. A volcanic eruption of lava will definitely occur within the next 24 hours. D. Magma is becoming less active underneath the volcano, which means there is no possible eruption
Magma is becoming more active underneath the volcano, which could lead to an eventual eruption. Option A is the correct choice.
If the surface around a volcano is swelling, it indicates that there is an increase in pressure from magma rising beneath the surface. This is often a sign of increased volcanic activity, which can eventually lead to an eruption. A few centimeters of swelling may not necessarily indicate an imminent eruption, but it does suggest that the magma is becoming more active and may lead to an eruption in the future.
Therefore, the most likely conclusion that the scientist would make based on this data is that magma is becoming more active underneath the volcano, which could lead to an eventual eruption. Therefore, option A is correct.
To know more about magma, here
brainly.com/question/16940653
#SPJ4
a perchloric acid solution has a ph of 3.158. what is the concentration of perchlorate ion in this solution?
The concentration of perchlorate ion in the solution that has a ph of 3.158 is 7.9 × 10−4 M.
Perchloric acid has the chemical formula HClO4. When it dissolves in water, it completely dissociates into H+ ions and ClO4- ions. The pH of a solution is defined as the negative logarithm of the hydrogen ion concentration [H+].A perchloric acid solution with a pH of 3.158 has an [H+] of 7.9 × 10−4 M, according to the following formula:
pH = −log [H+]
The concentration of the perchlorate ion [ClO4-] can be calculated using the following formula:
Kw = [H+][OH-] = 1 × 10-14 = [H+]2[H+] = 1 × 10-14[H+] = √(1 × 10-14) = 1 × 10-7M[OH-] = Kw/[H+] = (1 × 10-14) / (1 × 10-7) = 1 × 10-7M
The concentration of ClO4- is equal to the concentration of H+ because they are present in equal amounts as a result of complete dissociation of perchloric acid: [ClO4-] = [H+] = 7.9 × 10−4 M.
More on Perchloric acid: https://brainly.com/question/29089251
#SPJ11
how much volume in ml will you need to take from 3.8 m concentrated stock solution if you would like to prepare a diluted 0.9 solution with 100 ml? report and round your answer to a whole integer.
You will need to take 24 mL of the concentrated solution and add it to 76 mL of solvent to prepare 100 mL of a 0.9 M diluted solution.
The given data is as follows:
concentrated stock (C1)= 3.8 m
diluted solution (C2) = 0.9 m
Total available solution (V2)= 100ml
To find out the volume of the concentrated solution needed, we must use the formula
V1 x C1 = V2 x C2
By substituting the values we can get,
V1 x 3.8 M = 100 mL x 0.9 M
V1 = (100 mL x 0.9 M) / 3.8 M
V1 = 23.68 mL
Rounding to the nearest whole integer as mentioned we get:
V1 = 24 mL
Therefore, we can conclude that you will need to take 24 mL of the concentrated solution.
To learn more about Chemical Solutions
https://brainly.com/question/13182946
#SPJ4
solids, liquids, and gases all have kinetic energy due to motion of their atoms or molecules. which form of molecular motion do liquids experience? select all that apply. a. translational b. vibrational c. rotational d. transitional
Translational, rotational and transitional are the form of molecular motion that liquids experience. Therefore, the correct options are option A, C and D.
The only thing that constitutes molecular motion is the movement of its component parts in a certain plane. Temperature has an impact on how much the constituent particles move. The average kinetic energy of the molecules is also measured by the temperature. Heat is another factor that affects molecular mobility since it gives molecules more kinetic energy. Molecules in a liquid are continually moving. When the container is tilted, particles travel to the left and downward due to the pull of gravity, and the gaps are filled by numerous more molecules. The result is a general outflow of liquid from the vessel. Translational, rotational and transitional are the form of molecular motion that liquids experience.
Therefore, the correct options are option A, C and D.
To know more about molecular motion, here:
https://brainly.com/question/14240663
#SPJ12
calculate each of the following quantities in 0.160 mol of C6H14O. calculate the number of atoms of H. calculate the number of atoms of C.
Answer:
To calculate the number of atoms of H and C in 0.160 mol of C6H14O, we need to first determine the number of moles of each element present in C6H14O.
The molecular formula of C6H14O shows that there are 6 carbon atoms, 14 hydrogen atoms, and 1 oxygen atom in each molecule of C6H14O.
The molar mass of C6H14O can be calculated as:
Molar mass of C6H14O = (6 × atomic mass of C) + (14 × atomic mass of H) + (1 × atomic mass of O)
= (6 × 12.01 g/mol) + (14 × 1.01 g/mol) + (1 × 16.00 g/mol)
= 86.18 g/mol
Therefore, 0.160 mol of C6H14O has a mass of:
Mass = molar mass × number of moles
= 86.18 g/mol × 0.160 mol
= 13.79 g
Now we can calculate the number of atoms of H and C in 0.160 mol of C6H14O.
Number of atoms of H:
Number of moles of H = 14 × 0.160 mol = 2.24 mol
Number of atoms of H = 2.24 mol × Avogadro's number
= 2.24 mol × 6.022 × 10^23/mol
= 1.35 × 10^24 atoms of H
Therefore, there are 1.35 × 10^24 atoms of hydrogen in 0.160 mol of C6H14O.
Number of atoms of C:
Number of moles of C = 6 × 0.160 mol = 0.96 mol
Number of atoms of C = 0.96 mol × Avogadro's number
= 0.96 mol × 6.022 × 10^23/mol
= 5.78 × 10^23 atoms of C
Therefore, there are 5.78 × 10^23 atoms of carbon in 0.160 mol of C6H14O.
Explanation:
an unknown weak acid with a concentration of 0.058 m has a ph of 1.80. what is the ka of the weak acid?
Answer: The Ka of the weak acid with a concentration of 0.058 m and a pH of 1.80 is 0.0016.
The Ka of a weak acid is the product of the concentration of the hydrogen ion and the concentration of the conjugate base, divided by the concentration of the weak acid. The Ka of an unknown weak acid with a concentration of 0.058 m and a pH of 1.80 can be calculated as follows:
Ka = ([H+]*[A-])/[HA]
Ka = (10^(-1.8)*10^(-1.8))/0.058
Ka = 0.0016
Therefore, the Ka of the weak acid with a concentration of 0.058 m and a pH of 1.80 is 0.0016.
Learn more about acids here:
https://brainly.com/question/29796621#
#SPJ11
the pressure on a balloon holding 433 ml of an ideal gas is increased from 688 torr to 1.00 atm. what is the new volume of the balloon (in ml) at constant temperature?
Answer:
pressure on a balloon holding 433 ml of an ideal gas is increased from 688 torr to 1.00 atm. what is the newpressure on a balloon holding 433 ml of an ideal gas is increased from 688 torr to 1.00 atm. what is the new volume of the balloon (in ml) at constant temperature
which of the following is true of a hydrocarbon? group of answer choices it consists of carbon and hydrogen atoms. it can form a ring structure. it is a good fuel for combustion reactions. it can contain double or triple bonds. all of these
The following is true of a hydrocarbon is e. All of these
Hydrocarbon compounds are the simplest carbon compounds composed of carbon and hydrogen atoms that can form ring structures, are used as fuel for combustion reactions, and contain double or triple bonds.
The common characteristics of hydrocarbons are that they produce steam, carbon dioxide, and heat during combustion, and oxygen is required for the combustion reactions to occur. This compound is used as a fuel source. In everyday life we encounter many carbonate compounds, such as kerosene, gasoline, natural gas, and plastics. Other types of hydrocarbons such as propane and butane are used in Liquified Petroleum Gas and some materials for making medicine and clothing.
Learn more about hydrogen at:
https://brainly.com/question/29765115
#SPJ11