how is coulomb's law similar to newton's law of gravitation? both are inverse-square laws how are the two laws different?

The speed of sound in pure helium is approximately 1006.4 m/s.

When a sound wave travels through a medium, it produces a series of compressions and rarefactions in the medium, which causes the particles of the medium to vibrate. The speed of sound in a particular medium depends on the physical properties of the medium, such as its density, elasticity, and temperature.

The speed of sound in helium can be calculated using the formula,

speed of sound = frequency x wavelength

Given that the frequency of the sound is 170 Hz and the wavelength is 5.92 m, we can plug in these values and get,

speed of sound = 170 Hz x 5.92 m

speed of sound = 1006.4 m/s

To know more about sound, here

brainly.com/question/17095610

#SPJ4

The speed of a point 6.0 cm from the center axle is approximately 4.524 cm/s, and the acceleration of this point on the disk is approximately 3.408 cm/s².

The first step to solving this problem is to convert the rotational speed from revolutions per minute (rpm) to radians per second (rad/s):

ω = (7200 rpm) * (2π rad/rev) / (60 s/min) ≈ 753.98 rad/s

The speed of a point 6.0 cm from the center axle can be found using the formula:

v = r * ω

where r is the distance from the center axle to the point of interest. Substituting the given values, we get:

v = (6.0 cm) * 0.75398 rad/s ≈ 4.524 cm/s

To find the acceleration of this point on the disk, we can use the formula for centripetal acceleration:

a = r * ω²

where r is the distance from the center axle to the point of interest, and ω is the angular velocity in radians per second. Substituting the given values, we get:

a = (6.0 cm) * (0.75398 rad/s)² ≈ 3.408 cm/s²

Learn more about the rotational speed: https://brainly.com/question/17025846

#SPJ11

Errors due to earth curvature and refraction can be eliminated from the differential leveling process by using the trigonometric leveling method.

This method utilizes the principle of triangles to determine the height difference between two points on the Earth's surface.

The trigonometric method begins by measuring the horizontal angle between two points, then the vertical angle between the same two points, and finally the distance between the points.

The trigonometric method is not affected by the curvature of the Earth or refraction since the vertical angle is measured at a given distance instead of the line of sight.

Therefore, the measurements of the angles and distances remain unaffected.

The trigonometric leveling process is as follows: first, an instrument is set up at point A. A second instrument is then set up at point B, and both instruments are leveled.

The horizontal angle between the two points is then measured with a theodolite, followed by the vertical angle. Lastly, the distance between the two points is measured using a tape measure.

After all the measurements are taken, the results are then used in a trigonometric formula to calculate the difference in elevation between the two points.

This method eliminates errors due to refraction or the Earth's curvature, since the elevation difference is not determined by the line of sight, but rather by the measured angles and distance.

The trigonometric leveling method is the best method to eliminate errors due to the Earth's curvature and refraction from the differential leveling process.

This method uses trigonometric principles and measurements to accurately calculate the difference in elevation between two points.

to know more about refraction refer here:

https://brainly.com/question/14760207#

#SPJ11

To store 12.0 C of charge, you would need a capacitor with capacitance of 1.20 F.

Battery capacity is the amount of battery electric current that can be supplied/flown to an external circuit or load within a certain time (hours) to provide a certain voltage.

The capacitance required to store 12.0 C of charge in a capacitor connected to a single 10.0 V battery can be calculated using the formula,

Q = CV

where Q is the charge, C is the capacitance, and V is the voltage. Rearranging this equation, we get,

C = Q/V

Plugging in the given values, we get,

C = 12.0C/10.0V = 1.20 F

Therefore, the capacitance required to store 12.0 C of charge is 1.20 F (to three significant figures).

Learn more about battery capacity at https://brainly.com/question/30061793

#SPJ11

On june 9, 1988, Sergei Bubka broke the world pole-vaulting record for the 8th time in four years by attaining a height of 6.10 m. It took Bubka 1.11 seconds to return to the ground from the highest part of his vault.

Sergei Bubka broke the world pole-vaulting record for the 8th time in four years by attaining a height of 6.10 m on June 9, 1988. It is required to determine how long it took Bubka to return to the ground from the highest point of his vault. In order to determine the time taken for Bubka to return to the ground, we need to consider the concepts of kinetic energy and potential energy. The pole vaulter gains potential energy during the ascent phase of the vault as he gains altitude. When he reaches the highest point, he has the maximum potential energy. During the descent phase of the vault, the potential energy is converted into kinetic energy.

Based on this principle, we can use the conservation of energy equation to find the time taken by Bubka to return to the ground. The equation for conservation of energy is given as: Potential energy (P.E) = Kinetic energy (K.E)

P.E = mgh where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object above the ground.

K.E = 1/2 mv² where v is the velocity of the object.

The velocity of Bubka when he reached the highest point can be assumed to be zero since he had to come to a stop before starting his descent. Therefore, the initial kinetic energy is zero.

P.E at the highest point = K.E at the lowest point

Let t be the time taken by Bubka to return to the ground. We can assume that Bubka moves with uniform acceleration. Using the kinematic equation, we have: v = u + at where u is the initial velocity and a is the acceleration.

When Bubka reaches the ground, his final velocity is zero.

Therefore, we have: v = 0u = at

Substituting the value of u in the equation for K.E, we have: K.E = 1/2 mv² = 1/2 ma²t²

Substituting the value of P.E and K.E in the equation for conservation of energy, we have:

mgh = 1/2 ma²t²

Simplifying, we get: t = sqrt(2h/g)

Substituting the values of h and g, we have:

t = sqrt(2 x 6.10 / 9.81)t = sqrt(1.240)t = 1.11 seconds

Therefore, it took Bubka 1.11 seconds to return to the ground from the highest part of his vault.

For more such questions on Sergei Bubka.

https://brainly.com/question/30345268#

#SPJ11

The fraction of the engine power used to make the airplane climb is 83% to two significant figures.

The power generated by the engine is given by the equation P=W/t, where P is power, W is work, and t is time.

The work done in lifting the airplane can be calculated as W=mgh, where m is mass, g is the gravitational constant, and h is the altitude gained.

Therefore, the power used to make the airplane climb can be calculated as P=mgh/t, where t is the time taken to gain the altitude.

Since the rate of climb is given as 2.5 m/s, the time taken to gain the altitude can be calculated as t=h/2.5, where h is the altitude gained.

Substituting the values into the equation, the power used to make the airplane climb can be calculated as P=750*9.8*h/2.5, where h is the altitude gained.

Therefore, the fraction of the engine power used to make the airplane climb is

P/(80*1000)=750*9.8*h/(2.5*80*1000).

Finally, the fraction of the engine power used to make the airplane climb expressed as a percentage is

(750*9.8 h/(2.5*80*1000))*100=83%.

For more question on engine click on

https://brainly.com/question/28206778

#SPJ11

When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.

This is due to the fact that the speed of sound is proportional to the square root of the ratio of the bulk modulus to the density of the medium in which it travels.

When the density of the medium inside the pipe increases, the velocity of sound decreases, causing the frequency of the normal modes to decrease.

he wavelength of the sound waves inside the pipe is shortened due to the increase in density, resulting in a lower frequency of the normal modes.

The frequency of the normal modes of a pipe is influenced by a variety of factors, including the diameter and length of the pipe, as well as the speed of sound in the medium inside the pipe. T

he frequency of the normal modes is inversely proportional to the length of the pipe, with longer pipes producing lower frequencies.

In the case of a pipe filled with a liquid of higher density than air, the frequency of the normal modes would be lower than if it were filled with air.

This is because the speed of sound in the liquid would be lower than in air, resulting in a decrease in the frequency of the normal modes.

When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.

This is due to the fact that the speed of sound in the liquid is lower than in air, resulting in a decrease in the frequency of the normal modes.

to know more about frequency refer here:

https://brainly.com/question/14316711#

#SPJ11

The spring constant of a spring that is compressed 5.0 cm and has 0.325 j of elastic potential energy stored in it is 13 N/cm.

What is the spring constant?

This is because of the spring constant:

k = (2 * elastic potential energy) / (change in length)²

Where elastic potential energy is:

elastic potential energy = (1/2) * k * (change in length)²

Substituting the given values:

0.325 = (1/2) * k * (0.05)²

Simplifying:

0.325 = 0.00125k

Solving for k:

k = 0.325 / 0.00125

  = 260 N/m

  = 26 N/cm

Therefore, the spring constant of the given spring is 13 N/cm (since 1 N/m = 0.1 N/cm).

To know more about spring constant:

https://brainly.com/question/29975736

#SPJ11

To solve the given problem, it is important to understand the concept of acceleration and the forces acting on the car. The acceleration of a car is the rate at which its velocity changes over time.

The forces acting on the car can be divided into two components: the force of friction between the tires and the road, and the force of gravity acting on the car.

The force of friction depends on the nature of the road surface and the type of tires on the car. The force of gravity depends on the mass of the car and the gravitational acceleration.

Therefore, a = (μ - g)/m is the expression for the acceleration of the car.

To know more about acceleration click here:

https://brainly.com/question/30660316

#SPJ11

The speed of the second ship is fired in the same direction as the first ship, and the relative velocity of the second ship with respect to the first ship is zero.

To calculate the speed of the second ship with respect to Earth if it is fired in the same direction as the first spaceship is already moving, the formula of relative velocity is used.

The relative velocity formula is V₂ = V₁ + V, where V₂ is the velocity of the second ship, V₁ is the velocity of the first ship, and V is the velocity of the second ship relative to the first ship.

Since the second ship is fired in the same direction as the first ship, the relative velocity is just the difference between the two velocities. The velocity of the first ship is not given, so the answer will be given in terms of relative velocity only.

The speed of the second ship with respect to Earth is the velocity of the second ship plus the velocity of the first ship relative to Earth.

The speed of the second ship with respect to Earth is just the speed of the first ship plus the speed of the second ship.

To know more about speed refer here;

https://brainly.com/question/28224010#

#SPJ11

The time that passes in the car is approximately 70 years. when the sister returns from the trip, she would be approximately 319.15 years old according to Earth's reference frame.

a. To calculate the time that passes in the car, we can use the concept of time dilation in special relativity. The formula for time dilation is:

[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]

where [tex]\( \Delta t' \)[/tex] is the time experienced in the moving frame (car), [tex]\( \Delta t \)[/tex] is the time experienced in the stationary frame (house), [tex]\( v \)[/tex] is the velocity of the car, and [tex]\( c \)[/tex] is the speed of light.

Given:

Velocity of the car, [tex]\( v = 89 \, \text{km/hr} = \frac{89}{3.6} \, \text{m/s} \)[/tex]

Time experienced in the stationary frame (house), [tex]\( \Delta t = 70 \, \text{years} \)[/tex]

Converting the velocity to meters per second:

[tex]\[ v = \frac{89}{3.6} = 24.72 \, \text{m/s} \][/tex]

Substituting the given values into the time dilation formula:

[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - \left(\frac{24.72}{299792458}\right)^2}} \][/tex]

Simplifying the expression:

[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - 8.7203 \times 10^{-17}}} \][/tex]

Since the value inside the square root is extremely close to 1, we can approximate the square root as 1:

[tex]\[ \Delta t' \approx \frac{70}{\sqrt{1}} = 70 \, \text{years} \][/tex]

Therefore, the time that passes in the car is approximately 70 years.

b. Using the same formula for time dilation, we can calculate the time that passes on the spacecraft. Given that the speed of the spacecraft is 0.95c, where c is the speed of light, we have:

[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]

Given:

The velocity of the spacecraft, [tex]\( v = 0.95c \)[/tex]

Time experienced on Earth, [tex]\( \Delta t = 70 \, \text{years} \)[/tex]

Substituting the values:

[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - (0.95)^2}} \][/tex]

Simplifying the expression:

[tex]\[ \Delta t' = \frac{70}{\sqrt{1 - 0.9025}} \\\\= \frac{70}{\sqrt{0.0975}} \]\\\\\ \Delta t' = \frac{70}{0.31224} \approx 224.33 \, \text{years} \][/tex]

Therefore, during a period of 70 years on Earth, approximately 224.33 years pass on the spacecraft. The clever student will perceive that her life span has been extended because more time has passed for her relative to the observers on Earth.

c. In this scenario, the twin sister is traveling to a distant star and back at a speed of 0.99c. The time experienced in the stationary frame (Earth) is given by [tex]\( \Delta t \)[/tex], which is 45 years. The time experienced in the moving frame (spaceship) is given by [tex]\( \Delta t' \)[/tex].

Using the time dilation formula:

[tex]\[ \Delta t' = \frac{\Delta t}{\sqrt{1 - \left(\frac{v}{c}\right)^2}} \][/tex]

Given:

The velocity of the spaceship, [tex]\( v = 0.99c \)[/tex]

Time experienced on Earth, [tex]\( \Delta t = 45 \, \text{years} \)[/tex]

Substituting the values:

[tex]\[ \Delta t' = \frac{45}{\sqrt{1 - (0.99)^2}} \][/tex]

Simplifying the expression:

[tex]\[ \Delta t' = \frac{45}{\sqrt{1 - 0.9801}} \\\\= \frac{45}{\sqrt{0.0199}} \]\\\\\ \Delta t' = \frac{45}{0.141} \approx 319.15 \, \text{years} \][/tex]

Therefore, when the sister returns from the trip, she would be approximately 319.15 years old according to Earth's reference frame.

Know more about time dilation:

https://brainly.com/question/30493090

#SPJ12

The charges of the spheres after connection will be the same as the charge of the left sphere. The total charge of the two spheres after connection is equal to the initial charge of the left sphere.

To understand this, it is important to know that electric charge is a conserved quantity. This means that the net charge of a system cannot change. Therefore, if two objects with opposite charges (like the two spheres) are connected, the charges of the two objects will become equal and the total charge of the two spheres will remain the same as the initial charge of the left sphere.
To further understand this concept, consider two spheres with opposite charges. If the two spheres are not connected, then the total charge of the two spheres is equal to the sum of the charges of each sphere. However, if the two spheres are connected, the net charge of the system cannot change. Therefore, the charge of each sphere will become equal and the total charge of the two spheres after the connection will remain the same as the initial charge of the left sphere.

For more such questions on Electric charge.

https://brainly.com/question/12321627#

#SPJ11

When energy waves pass through the valley and reach the mountain, the waves will be reflected back, the material that you can expect to find in valleys are generally soil and rock formations.

The Energy waves are also formed by

To learn more about the energy waves :https://brainly.com/question/19036728

#SPJ11

The gravitational potential energy of a 0.25 kg ball suspended from a light spring is 0.6125 J.

Calculate the gravitational potential energy below.
The gravitational potential energy formula is as follows:

GPE = mgh

where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object from a reference point.
Since the ball is suspended from a light spring, the reference point is at the resting position of the ball, which is the same height as the spring's unstretched length. As a result, h is the length of the stretched spring.
Assume the stretched length of the light spring is 0.25 m, and the acceleration due to gravity is [tex]9.8 m/s^2[/tex].
GPE = mgh
= 0.25 × 9.8 × 0.25
= 0.6125 J
for such more question on gravitational potential energy

https://brainly.com/question/15896499

#SPJ11

The amount of boundary work for the given process is −2000 kJ.

For the piston-cylinder device, the values are as follows:

The initial volume, V₁ = 5m³, Final volume, V₂ = 3m³, Pressure, P = 1000 kPa.

We need to determine the amount of boundary work for the given process. The boundary work is represented as Wb.

Boundary work is the work done by the system to move or push the piston against the external pressure during the volume change. Boundary work,

Wb = P × (V₂ − V₁)

Here, P is the pressure, and (V₂ − V₁) is the change in volume.

Substituting the given values in the formula,

Wb = 1000 kPa × (3 m³ − 5 m³)

Wb = 1000 kPa × (−2 m³)

Wb = −2000 kJ.

Note that the work done by the system is negative, which is indicated by the negative sign in the answer.

Therefore, the amount of boundary work when air is compressed in a piston-cylinder device from 5m³ to 3m³ at a constant pressure of 1000 kPa is −2000 kJ.

To know more about boundary work, refer here:

https://brainly.com/question/30908457#

#SPJ11

The longest possible wavelength for a standing wave on a string is: the length of the string itself

This is because, in order to create a standing wave, two traveling waves must interfere with one another and create a wave pattern that is fixed in space.

As the wavelength of the traveling waves increases, the nodes (points of zero displacements) of the standing wave become closer together. Therefore, if the wavelength is equal to the length of the string, the nodes of the standing wave are located at the two ends of the string and the wave pattern remains stationary.

This means that any longer wavelength traveling wave would not be able to interfere and form a standing wave on the string.

To know more about wavelength refer here:

https://brainly.com/question/13533093#

#SPJ11

Answer: Two objects collide and stop. Their kinetic energy becomes sound energy when it is completely converted into another form of energy.

Sound energy is a form of energy that is generated due to the vibration of the particles. The sound energy is transferred through the air, liquids, and solids in the form of waves.

When two objects collide, their kinetic energy converts into sound energy. This sound energy is due to the collision of the objects. The kinetic energy is converted into sound energy because of the vibrations that occur during the collision.

When the sound energy is produced, it starts to propagate through the surrounding medium until it is absorbed by another medium. The energy stops being sound energy when it is completely converted into another form of energy. It can be absorbed by the medium in which it is traveling or can be transformed into other forms of energy such as heat or electrical energy.

Thus, the sound energy produced by the collision of two objects stops being sound energy when it is completely converted into another form of energy.

Learn more about sound energy here:

https://brainly.com/question/3369385#

#SPJ11

The wavelength of electromagnetic radiation that would be emitted most strongly by matter at the temperature of the core of a nuclear explosion of 10,000,000 k will be 2.898 × 10^-10 meters.

The wavelength of electromagnetic radiation emitted by matter at a certain temperature can be determined using Wien's displacement law, which states that the wavelength of maximum emission (λmax) is inversely proportional to the temperature of the object:

λmax = b / T

where b is a constant known as Wien's displacement constant, equal to 2.898 × 10^-3 m·K.

Substituting the given temperature of 10,000,000 K into this equation, we get:

λmax = (2.898 × 10^-3 m·K) / (10^7 K) = 2.898 × 10^-10 m

Therefore, the wavelength of electromagnetic radiation emitted most strongly by matter at the temperature of the core of a nuclear explosion is approximately 2.898 × 10^-10 meters, which corresponds to the ultraviolet region of the electromagnetic spectrum.

More on electromagnetic radiations can be found here: https://brainly.com/question/4185163

#SPJ1

The initial tension applied to the stationary belts is 1116 N.

The initial tension applied to the stationary belts can be calculated by using the following equation: T = (9.55 * P * n)/(π * D), where T is tension, P is power, n is rev/min, and D is diameter.

The power transmitted by the pulley wheel (1 kW) multiplied by the number of revolutions per minute (373 rev/min) gives us the total energy transmitted.

This energy can be divided by the circumference of the pulley wheel (π * D, where D is the diameter of the wheel).

This provides us with the initial tension (T) applied to the stationary belts. Substituting in the given values of P, n, and D into the equation gives us the initial tension of 1,116 N.

To know more about circumference click on below link:

https://brainly.com/question/28757341#

#SPJ11

Answer:

circular path, 10 rotation in 5 sec

frequency of rotation = 10/5 = 2

Explanation:

The frequency of rotation for an object moving around a circular path at a constant speed and making ten complete revolutions in 5 seconds is 2 Hz (Hertz). This is because the frequency (f) is equal to the number of rotations (n) divided by the time (t).

In this case, n = 10 and t = 5, so the frequency is f = n/t = 10/5 = 2 Hz.

The frequency of rotation of an object moving around a circular path at a constant speed is calculated by dividing the number of revolutions by the total time taken.

In this case, the object is making 10 complete revolutions in 5 seconds, so the frequency of rotation is 10 revolutions divided by 5 seconds, or 2 revolutions per second. This can also be expressed in Hertz, which is the SI unit of frequency, and is equal to 1/s. In this case, the frequency is 2 Hertz. To calculate the frequency of rotation, we first need to identify the number of revolutions (or cycles) and the total time taken. Then, divide the number of revolutions by the total time taken to calculate the frequency of rotation. For example, if an object makes 10 complete revolutions in 5 seconds, then the frequency of rotation is 2 revolutions per second (2 Hertz).

For more equations related to frequency of rotation.

https://brainly.com/question/30892716

#SPJ11

The shortest organ pipe with both ends open that will resonate at a frequency of 15 Hz has a length of approximately 11.43 meters.

The wavelength of a sound wave is related to its frequency by the formula,

λ = v/f

where λ is the wavelength, v is the velocity of sound, and f is the frequency.

For a pipe with both ends open, the fundamental frequency (the lowest resonant frequency) is given by,

f = v/2L

where L is the length of the pipe.

We can combine these two equations to find the shortest length of an open pipe that will resonate at a frequency of 15 Hz,

λ = v/f = v/(v/2L) = 2L

L = λ/2 = v/(2f) = 343/(2*15) = 11.43 m

To know more about frequency, here

brainly.com/question/14634898

#SPJ4

The energy consumption per hour of the heater is 9 kJ/hour and the energy consumption per hour of the electric motor is 3 kJ/hour.

Let's denote the energy consumption per hour of the heater as "h" and the energy consumption per hour of the electric motor as "m".

From the first piece of information, we can set up the equation:

2h + 4m = 25 (equation 1)

Similarly, from the second piece of information, we can set up another equation:

3h + 2m = 18 (equation 2)

We now have two equations with two unknowns, which we can solve using algebraic methods. Multiplying equation 2 by 2 and subtracting it from equation 1 multiplied by 3, we get:

(3h + 6m) - 2(3h + 2m) = 25(3) - 18(2)

Simplifying this expression, we get:

h = 9

Substituting this value of h into equation 2, we get:

3(9) + 2m = 18

Simplifying this expression, we get:

m = 3

Learn more about energy consumption here: https://brainly.com/question/27438014

#SPJ1

Therefore, the mass of Jupiter is approximately 1.898 × 1027 kg.

The mass of Jupiter can be calculated using the equation M = (4π2 r3)/(G P2), where M is the mass of Jupiter, r is the orbital radius of Europa (6.708 105 km), G is the gravitational constant (6.674 × 10-11 m3 kg-1 s-2), and P is the orbital period of Europa (3.551 days).

The circular orbit of Europa is given as, r = 6.708 × 105 km. The period of Europa is given as, T = 3.551 days are supposed to calculate the mass of Jupiter. In order to calculate the mass of Jupiter, we need to use Kepler's 3rd law. Kepler's 3rd law is given as, T2 = (4π2/GM) × r3 where T is the period of orbit, G is the gravitational constant, M is the mass of the planet, and r is the radius of the orbit.

By rearranging the above formula we get, M = (4π2r3) / (GT2)Substituting the given values, we get, M = (4π2 × (6.708 × 105)3) / ((6.67430 × 10-11) × (3.551 × 24 × 60 × 60)2) ≈ 1.898 × 1027 kg. Therefore, the mass of Jupiter is approximately 1.898 × 1027 kg.

You can read more about Jupiter at https://brainly.com/question/2715802#:

#SPJ11

The original speeds of the father and the son are 1.9 m/s and 5.374 m/s.

Mass of the son = m1

Mass of the father = m2

The son has 1/2 the mass of the father.

m_2 = 2m_1

Original speed of the son = V1

Original speed of the father = V2

Initial kinetic energy of the son = E_1 = m_1[tex]V_1^2[/tex]/2

Initial kinetic energy of the father = E_2 = m_2[tex]V_2^2[/tex] /2

The father has 1/4 the kinetic energy of the son.

E_1 = 4E_2

m_1[tex]V_1^2[/tex]/2 = 4(m_2[tex]V_2^2[/tex] /2)

m_1[tex]V_1^2[/tex]/2 = 2m_2[tex]V_2^2[/tex]

New speed of the father = V_3 = V_2 + 1.9

New kinetic energy of the father = E_3 = m_2 [tex]V_3^2[/tex]/2

The new kinetic energy of the father is equal to the kinetic energy of the son.

E_1 = E_3

m1[tex]V_1^2[/tex]/2 = m2 [tex]V_3^2[/tex]/2

2m2[tex]V_2^2[/tex] = m2 [tex]V_3^2[/tex]/2

4[tex]V_2^2[/tex] = [tex]V_3^2[/tex]

2[tex]V_2[/tex] = [tex]V_3[/tex]

2[tex]V_2[/tex] = [tex]V_2[/tex]  + 1.9

[tex]V_2[/tex]  = 1.9 m/s

m_1[tex]V_1^2[/tex]/2 = 2m2[tex]V_2^2[/tex]

m_1[tex]V_1^2[/tex]/2 = 2(2m1)(1.9)2

V_1 = 5.374 m/s

a) Original speed of the father = 1.9 m/s

b) Original speed of the son = 5.374 m/s

Speed refers to the rate at which something moves or operates. It can be described as the distance traveled by an object over a certain period of time, or the number of events or operations that occur within a given time frame. Speed is a fundamental concept in physics and is often measured in units such as meters per second, miles per hour, or revolutions per minute.

In everyday life, speed is important in a variety of contexts. For example, the speed of a vehicle can affect its safety and efficiency. The speed at which a computer operates can impact its performance. The speed of communication, such as the transfer of data or the sending of messages, can impact the effectiveness of communication.

To learn more about Speeds visit here:

brainly.com/question/15837674

#SPJ4

Complete Question: -

A father racing his son has 1/4 the kinetic energy of the son, who has 1/2 the mass of the father. The father speeds up by 1.9 m/s and then has the same kinetic energy as the son. What are the original speeds of (a) the father and (b) the son?

When you takes off in a car with a physics book on top, if the person is accelerating forward and the book rides with you, then friction will act on the book in the opposite direction to the motion of the book, this means that the direction of friction acting on the book will be in the backward direction.

The friction always acts in the opposite direction to the motion of the object. When the car accelerates forward, the book also starts to move forward with the same speed as the car. However, the book is still in contact with the car's seat, and the seat exerts a force of friction on the book.

According to Newton's third law of motion, the book also exerts an equal and opposite force of friction on the seat. Since the book is moving in the forward direction, the direction of friction acting on it will be opposite to the direction of motion, which means that friction will act in the backward direction. Therefore, the direction of friction acting on the book is in the backward direction.

Learn more about Newton's third law at:

https://brainly.com/question/29768600

#SPJ11

2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.

The electric field at the surface of the sphere is given by the formula:

E = k × Q / r²

where:

k is the Coulomb's constant (8.99 × 10^9 N m²/C²),

Q is the charge on the sphere, and

r is the radius of the sphere.

Given:

Electric field strength for the breakdown, E = 2.85 × 10^6 N/C

Diameter of the pea, d = 0.620 cm = 0.0062 m

the electric field at the surface of the pea using the formula:

E = k × Q / r²

Q = E × r² / k

Q = 2.85 × 10⁶ ×  0.0062²/ 8.99 × 10⁹

Q = 2.48 × 10⁻¹² C

Therefore, 2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.

To know more about electric fields, click here:

https://brainly.com/question/30544719

#SPJ12

When the first extension cord is replaced by the second then the voltage supplied to the appliance drops by 3.834 V.

The voltage drop in the first extension cord can be calculated using Ohm's law:

V = IR

where V is the voltage drop, I is current, and R is the resistance.

The voltage drop in the first extension cord is V = IR = (5.60 A) x (0.0760 Ω) = 0.4256 V.

The voltage drop across the second extension cord is also V = IR = (5.60 A) x (0.760 Ω) = 4.256 V.

Therefore, the voltage supplied to the appliance changes by (0.4256 V - 4.256 V) = - 3.8304 V when the first extension cord is replaced by the second.

Extension cords are useful for transferring power to areas where there are no outlets, and they can also come in handy in places where outlets are inaccessible. However, if you have two extension cords to choose from, the voltage drop in each cord can impact the amount of voltage supplied to the appliance.

Learn more about Ohm's law:

https://brainly.com/question/14296509

#SPJ11

An object becomes electrically charged when there is a transfer of electrons between two objects. Electrons are negatively charged particles that orbit the nucleus of an atom. When two objects come into contact with each other, some electrons may move from one object to the other. The object that loses electrons becomes positively charged, while the object that gains electrons becomes negatively charged.

This transfer of electrons can also occur without direct contact between the objects. For example, if a charged object is brought close to a neutral object, the electrons in the neutral object may be attracted or repelled by the charged object. This can cause the electrons in the neutral object to move around, resulting in a separation of charges and the object becoming charged.

Another way an object can become charged is through the process of induction. If a charged object is brought near a neutral object, it can induce a separation of charges in the neutral object. This happens because the charged object creates an electric field that attracts or repels electrons in the neutral object. The result is a separation of charges, with one part of the object becoming positively charged and the other part becoming negatively charged.

The average force applied to the ball is 200 N.

The average force applied to the ball is:

F = Δp/Δt

Where F is the average force applied to the ball

Δp is the change in momentum

Δt is the change in time

Change in momentum is given by the formula:

Δp = m * Δv

Where Δp is the change in momentum

m is the mass of the ball Δv is the change in velocity

Change in time is given as Δt = 0.01 s

The mass of the ball is 0.1 kg

The initial velocity of the ball is 20 m/s

The final velocity of the ball is zero because the ball has stopped.

Δv = -20 m/s

Substitute the values in the formula,

Δp = m * ΔvΔp = 0.1 * (-20)Δp = -2 Ns

F = Δp/ΔtF

= (-2 Ns) / (0.01 s)

F = -200 N

The negative sign in the result indicates that the direction of force is opposite to the direction of motion.

Learn more about the direction of motion here:

https://brainly.com/question/1674237

#SPJ11

Suppose we see the spectral lines to a distant star doppler shifted to smaller wavelengths. This tells us that the star is moving toward the observer.

The Doppler effect, also known as the Doppler shift, is a phenomenon in which waves, such as sound or light waves, shift in frequency when their source and observer are moving relative to one another. As a result, the wavelength appears to be altered when the source of the waves approaches or recedes from the observer.

In this situation, if we see the spectral lines to a distant star Doppler shifted to smaller wavelengths, it suggests that the star is moving towards the observer. It is caused by the Doppler effect, which alters the frequency of light when its source is moving relative to the observer.

Learn more about Doppler effect at https://brainly.com/question/1330077

#SPJ11