suppose the polar ice caps melted sending water towards the equator and increasing the moment of inertia of the earth by 1.1. the angular velocity of the earth will be

The statement "pry on the power steering reservoir to adjust the tension of the power steering belt" is: false.

The tension of the power steering belt is adjusted by adjusting the position of the power steering pump. There is a tension adjustment bolt on the power steering pump that is used to adjust the tension of the power steering belt. The adjustment bolt should be turned clockwise or counterclockwise to adjust the tension of the belt.

A belt tension gauge may be used to ensure that the belt is properly tensioned. A pry bar should not be used on the power steering reservoir to adjust the tension of the power steering belt. This could cause damage to the reservoir or other components of the power steering system. The reservoir should be inspected for damage or leaks, but it should not be used to adjust the tension of the belt.

In summary, the tension of the power steering belt should be adjusted by adjusting the position of the power steering pump, not by prying on the power steering reservoir.

To know more about tension refer here:

https://brainly.com/question/29869473#

#SPJ11

Yes, the magnitude of the force on the lower book by the upper book in the elevator situation is equal to the weight of the upper book. This can be expressed as F = mg,

The expression for the magnitude of the force on the lower book by the upper book in the elevator situation is;

F(lower on upper) = (m(lower) + m(upper))g

Where F(lower on upper) is the magnitude of the force on the lower book by the upper book,

m(lower) is the mass of the lower book,

m(upper) is the mass of the upper book and

g is the acceleration due to gravity.

Therefore, the magnitude of the force on the lower book by the upper book is not equal to the weight of the upper book since it takes into account the mass of the lower book as well.

To know more about magnitude:

https://brainly.com/question/2596740

#SPJ11

The speed of the second ship is fired in the same direction as the first ship, and the relative velocity of the second ship with respect to the first ship is zero.

To calculate the speed of the second ship with respect to Earth if it is fired in the same direction as the first spaceship is already moving, the formula of relative velocity is used.

The relative velocity formula is V₂ = V₁ + V, where V₂ is the velocity of the second ship, V₁ is the velocity of the first ship, and V is the velocity of the second ship relative to the first ship.

Since the second ship is fired in the same direction as the first ship, the relative velocity is just the difference between the two velocities. The velocity of the first ship is not given, so the answer will be given in terms of relative velocity only.

The speed of the second ship with respect to Earth is the velocity of the second ship plus the velocity of the first ship relative to Earth.

The speed of the second ship with respect to Earth is just the speed of the first ship plus the speed of the second ship.

To know more about speed refer here;

https://brainly.com/question/28224010#

#SPJ11

All of the given options produce an acceleration that are force pairs suggested in Question 5.

When a skier uses her ski poles to start moving downhill then the ski poles exert a backward force on the ground while the ground exerts a forward force on poles and produces acceleration.

Similarly in case B. when a boat propeller spins rapidly in the water the propeller exert a backward force on the water while the water exerts a forward force on propeller and produces acceleration.

In case C. when a baseball player hits a pitched ball with a bat the bat exert a backward force on the ball while the ball exerts a force away from bat and produces acceleration.

In case D. when a party balloon contains rapidly moving helium atoms the helium atoms exert an outward force on the balloon while the balloon exerts an inward force on helium atoms and produces acceleration.

To learn more about acceleration click here https://brainly.com/question/12550364

#SPJ1

The amount of boundary work for the given process is −2000 kJ.

For the piston-cylinder device, the values are as follows:

The initial volume, V₁ = 5m³, Final volume, V₂ = 3m³, Pressure, P = 1000 kPa.

We need to determine the amount of boundary work for the given process. The boundary work is represented as Wb.

Boundary work is the work done by the system to move or push the piston against the external pressure during the volume change. Boundary work,

Wb = P × (V₂ − V₁)

Here, P is the pressure, and (V₂ − V₁) is the change in volume.

Substituting the given values in the formula,

Wb = 1000 kPa × (3 m³ − 5 m³)

Wb = 1000 kPa × (−2 m³)

Wb = −2000 kJ.

Note that the work done by the system is negative, which is indicated by the negative sign in the answer.

Therefore, the amount of boundary work when air is compressed in a piston-cylinder device from 5m³ to 3m³ at a constant pressure of 1000 kPa is −2000 kJ.

To know more about boundary work, refer here:

https://brainly.com/question/30908457#

#SPJ11

The speed of sound in pure helium is approximately 1006.4 m/s.

When a sound wave travels through a medium, it produces a series of compressions and rarefactions in the medium, which causes the particles of the medium to vibrate. The speed of sound in a particular medium depends on the physical properties of the medium, such as its density, elasticity, and temperature.

The speed of sound in helium can be calculated using the formula,

speed of sound = frequency x wavelength

Given that the frequency of the sound is 170 Hz and the wavelength is 5.92 m, we can plug in these values and get,

speed of sound = 170 Hz x 5.92 m

speed of sound = 1006.4 m/s

To know more about sound, here

brainly.com/question/17095610

#SPJ4

The initial tension applied to the stationary belts is 1116 N.

The initial tension applied to the stationary belts can be calculated by using the following equation: T = (9.55 * P * n)/(π * D), where T is tension, P is power, n is rev/min, and D is diameter.

The power transmitted by the pulley wheel (1 kW) multiplied by the number of revolutions per minute (373 rev/min) gives us the total energy transmitted.

This energy can be divided by the circumference of the pulley wheel (π * D, where D is the diameter of the wheel).

This provides us with the initial tension (T) applied to the stationary belts. Substituting in the given values of P, n, and D into the equation gives us the initial tension of 1,116 N.

To know more about circumference click on below link:

https://brainly.com/question/28757341#

#SPJ11

The energy consumption per hour of the heater is 9 kJ/hour and the energy consumption per hour of the electric motor is 3 kJ/hour.

Let's denote the energy consumption per hour of the heater as "h" and the energy consumption per hour of the electric motor as "m".

From the first piece of information, we can set up the equation:

2h + 4m = 25 (equation 1)

Similarly, from the second piece of information, we can set up another equation:

3h + 2m = 18 (equation 2)

We now have two equations with two unknowns, which we can solve using algebraic methods. Multiplying equation 2 by 2 and subtracting it from equation 1 multiplied by 3, we get:

(3h + 6m) - 2(3h + 2m) = 25(3) - 18(2)

Simplifying this expression, we get:

h = 9

Substituting this value of h into equation 2, we get:

3(9) + 2m = 18

Simplifying this expression, we get:

m = 3

Learn more about energy consumption here: https://brainly.com/question/27438014

#SPJ1

The gravitational potential energy of a 0.25 kg ball suspended from a light spring is 0.6125 J.

Calculate the gravitational potential energy below.
The gravitational potential energy formula is as follows:

GPE = mgh

where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object from a reference point.
Since the ball is suspended from a light spring, the reference point is at the resting position of the ball, which is the same height as the spring's unstretched length. As a result, h is the length of the stretched spring.
Assume the stretched length of the light spring is 0.25 m, and the acceleration due to gravity is [tex]9.8 m/s^2[/tex].
GPE = mgh
= 0.25 × 9.8 × 0.25
= 0.6125 J
for such more question on gravitational potential energy

https://brainly.com/question/15896499

#SPJ11

77.7 g sample of gold will occupy a volume of 4 cm3.

A 77.7 g sample of gold will occupy a volume of 4 cm3, as calculated by using the equation D = m/V, where D is the density of gold (0.01932 kg/cm3), m is the mass of gold (77.7 g), and V is the volume of gold (4 cm3).

The mass needs to be converted from grams to kilograms, and the volume needs to be calculated. Divide the mass of gold (77.7 g) by 1,000:

m (in kg) = 77.7 g ÷ 1,000 = 0.0777 kg

V = m/D

V = 0.0777 kg ÷ 0.01932 kg/cm3 = 4 cm3

Therefore, a 77.7 g sample of gold will occupy a volume of 4 cm3.

to know more about volume refer here:

https://brainly.com/question/13338592#

#SPJ11

Answer:

1. A string of length 1.23 m vibrates in such a way that a standing wave with wavelength 0.820 m forms. What harmonic is the string vibrating at?

The original speeds of the father and the son are 1.9 m/s and 5.374 m/s.

Mass of the son = m1

Mass of the father = m2

The son has 1/2 the mass of the father.

m_2 = 2m_1

Original speed of the son = V1

Original speed of the father = V2

Initial kinetic energy of the son = E_1 = m_1[tex]V_1^2[/tex]/2

Initial kinetic energy of the father = E_2 = m_2[tex]V_2^2[/tex] /2

The father has 1/4 the kinetic energy of the son.

E_1 = 4E_2

m_1[tex]V_1^2[/tex]/2 = 4(m_2[tex]V_2^2[/tex] /2)

m_1[tex]V_1^2[/tex]/2 = 2m_2[tex]V_2^2[/tex]

New speed of the father = V_3 = V_2 + 1.9

New kinetic energy of the father = E_3 = m_2 [tex]V_3^2[/tex]/2

The new kinetic energy of the father is equal to the kinetic energy of the son.

E_1 = E_3

m1[tex]V_1^2[/tex]/2 = m2 [tex]V_3^2[/tex]/2

2m2[tex]V_2^2[/tex] = m2 [tex]V_3^2[/tex]/2

4[tex]V_2^2[/tex] = [tex]V_3^2[/tex]

2[tex]V_2[/tex] = [tex]V_3[/tex]

2[tex]V_2[/tex] = [tex]V_2[/tex]  + 1.9

[tex]V_2[/tex]  = 1.9 m/s

m_1[tex]V_1^2[/tex]/2 = 2m2[tex]V_2^2[/tex]

m_1[tex]V_1^2[/tex]/2 = 2(2m1)(1.9)2

V_1 = 5.374 m/s

a) Original speed of the father = 1.9 m/s

b) Original speed of the son = 5.374 m/s

Speed refers to the rate at which something moves or operates. It can be described as the distance traveled by an object over a certain period of time, or the number of events or operations that occur within a given time frame. Speed is a fundamental concept in physics and is often measured in units such as meters per second, miles per hour, or revolutions per minute.

In everyday life, speed is important in a variety of contexts. For example, the speed of a vehicle can affect its safety and efficiency. The speed at which a computer operates can impact its performance. The speed of communication, such as the transfer of data or the sending of messages, can impact the effectiveness of communication.

To learn more about Speeds visit here:

brainly.com/question/15837674

#SPJ4

Complete Question: -

A father racing his son has 1/4 the kinetic energy of the son, who has 1/2 the mass of the father. The father speeds up by 1.9 m/s and then has the same kinetic energy as the son. What are the original speeds of (a) the father and (b) the son?

2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.

The electric field at the surface of the sphere is given by the formula:

E = k × Q / r²

where:

k is the Coulomb's constant (8.99 × 10^9 N m²/C²),

Q is the charge on the sphere, and

r is the radius of the sphere.

Given:

Electric field strength for the breakdown, E = 2.85 × 10^6 N/C

Diameter of the pea, d = 0.620 cm = 0.0062 m

the electric field at the surface of the pea using the formula:

E = k × Q / r²

Q = E × r² / k

Q = 2.85 × 10⁶ ×  0.0062²/ 8.99 × 10⁹

Q = 2.48 × 10⁻¹² C

Therefore, 2.48 × 10⁻¹² C charge can be packed onto a green pea before the pea spontaneously discharges.

To know more about electric fields, click here:

https://brainly.com/question/30544719

#SPJ12

Option D: 2 m/s is the average velocity of the water flowing through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s.

According to the question:

cross-sectional area of the pipe = 0.002m²

Mass flowrate = 4 kg/s

Density of water = 1000 kg/m³

We are asked to find, average velocity =?

Average velocity is the net or total displacement covered by a body in a given time. The mass flow rate divided by the pipe's cross-sectional area and density ratio is the formula for calculating a fluid's average velocity.

As a result, the water's average flow rate through the pipe is provided by:

v = m / (ρ × A)

where, v is the average velocity, m is the mass flow rate, ρ is the density of water, and A is the cross-sectional area of the pipe. Substituting the values in the above equation we get:

v = 4 / (1000 × 0.002)

v = 2m/s

Therefore, the average velocity of water flowing through a pipe of cross-sectional area of 0.002m² is 2m/s.

To know more about average velocity, refer:

https://brainly.com/question/13243044

#SPJ4

Correct question is:

Water flows through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s. The density of water is 1 000 kg/m3. Determine its average velocity. Multiple choice question.

20 m/s

200 m/s

0.02 m/s

2 m/s

0.2 m/s

The magnitude and direction of the net force on the center charge is 3.929 x 10⁻⁴ N.

The unit of charge is the Coulomb (C). It is named after French physicist Charles-Augustin de Coulomb and is defined as the amount of electric charge that flows through a circuit when a current of one ampere flows for one second. One Coulomb is also equivalent to the charge on approximately 6.24 x 10¹⁸ electrons. The Coulomb is one of the seven base SI units (International System of Units) and is used to measure electric charge in physics and engineering.

So, the magnitude of the net force on the center charge is 3.929 x 10⁻⁴ N. Since F12 is directed towards the left, and F23 is directed towards the right, the net force is also directed towards the left. Therefore, the direction of the net force on the center charge is to the left.

According to Coulomb's law to calculate the force exerted by each of the other charges on the center charge, and then add them vectorially.

Let's call the left charge Q1, the center charge Q2, and the right charge Q3.

The force exerted on Q2 by Q1 is given by:

F₁₂ = k * |Q1| * |Q2| / r₁₂²

where k is Coulomb's constant, |Q1| and |Q2| are the magnitudes of the charges, and r₁₂ is the distance between them. Since Q1 is positive and Q2 is negative, the force F₁₂ is attractive and directed towards Q1. Because the distance between them is 2m, we can say:

F₁₂ = 9 x 10⁹ Nm²/C² * |52 x 10⁻⁶ C| * |3.10 x 10⁻⁶ C| / (2m)²

= 3.468 x 10⁻⁴ N (attractive)

The force exerted on Q2 by Q3 is given by:

F₂₃ = k * |Q2| * |Q3| / r₂₃²

where |Q3| is positive, and |Q2| is negative, so the force F23 is repulsive and directed away from Q3. The distance between them is also 2m, so:

F₂₃ = 9 x 10⁹ Nm²/C² * |3.10 x 10⁻⁶ C| * |68 x 10⁻⁶ C| / (2m)²

= 5.383 x 10⁻⁵ N (repulsive)

To find the net force on Q2, we need to add these two forces vectorially. Since they act along the same line, we can simply subtract their magnitudes:

Fnet = |F₁₂| - |F₂₃|

= 3.468 x 10⁻⁴ N - 5.383 x 10⁻⁵N

= 3.929 x 10⁻⁴ N.

To know more about Coulomb's law, visit:

https://brainly.com/question/9261306

#SPJ1

The magnetic field at a distance of 58.3 cm from a long, straight wire carrying a 23.9 A current, the strength of the resulting magnetic field can be found using the equation B = μ0*I/2π*r, where B is the magnetic field strength, μ0 is the permeability of free space, I is current, and r is the distance.

Therefore, the strength of the magnetic field at 58.3 cm from the wire is B = 4π * 10-7 * 23.9/2π * 58.3 = 0.0067 N/Amp.

The magnetic field strength due to the current in the wire is caused by the current producing a magnetic field, which is a result of moving electric charges (electrons) in the wire. The strength of the magnetic field depends on the magnitude of the current and the distance from the wire.

As the current increases, the magnetic field strength increases; likewise, as the distance from the wire increases, the magnetic field strength decreases. The direction of the magnetic field can be determined using the right-hand rule.

The strength of the magnetic field can be used to calculate the force on a moving charged particle, F = q * v * B, where q is the charge of the particle, v is its velocity, and B is the magnetic field strength. By using this equation, the force acting on a charged particle due to the magnetic field at 58.3 cm from the wire can be found.

To know more about magnetic field refer here:

https://brainly.com/question/23096032#

#SPJ11

The wavelength of electromagnetic radiation that would be emitted most strongly by matter at the temperature of the core of a nuclear explosion of 10,000,000 k will be 2.898 × 10^-10 meters.

The wavelength of electromagnetic radiation emitted by matter at a certain temperature can be determined using Wien's displacement law, which states that the wavelength of maximum emission (λmax) is inversely proportional to the temperature of the object:

λmax = b / T

where b is a constant known as Wien's displacement constant, equal to 2.898 × 10^-3 m·K.

Substituting the given temperature of 10,000,000 K into this equation, we get:

λmax = (2.898 × 10^-3 m·K) / (10^7 K) = 2.898 × 10^-10 m

Therefore, the wavelength of electromagnetic radiation emitted most strongly by matter at the temperature of the core of a nuclear explosion is approximately 2.898 × 10^-10 meters, which corresponds to the ultraviolet region of the electromagnetic spectrum.

More on electromagnetic radiations can be found here: https://brainly.com/question/4185163

#SPJ1

The longest possible wavelength for a standing wave on a string is: the length of the string itself

This is because, in order to create a standing wave, two traveling waves must interfere with one another and create a wave pattern that is fixed in space.

As the wavelength of the traveling waves increases, the nodes (points of zero displacements) of the standing wave become closer together. Therefore, if the wavelength is equal to the length of the string, the nodes of the standing wave are located at the two ends of the string and the wave pattern remains stationary.

This means that any longer wavelength traveling wave would not be able to interfere and form a standing wave on the string.

To know more about wavelength refer here:

https://brainly.com/question/13533093#

#SPJ11

c the forces that are inward forces are ;F3 and f4

d. The centrifugal force is the outward force

e. equation is force = mu²/r

F. there would be no restriction at B

d. Along with circular motion, there will be centrifugal force (pseudo force) in the outer direction. It will exert an opposite force to that of inward forces.

(f) The path will not be constrained after point B. As a result, until a force acts on the puck, it will move in a straight line in accordance with Newton's first law. It will follow the straight line you have shown in the image since it is moving at a constant speed, v.

(g) The velocity vector will always move in the circular path's tangential direction (tangent to the circular fence). The circular path's center is always where the centripetal acceleration will act (in the normal direction of the circular path).

(h & I). The puck is moving in a circular motion while just altering its speed's direction and not its magnitude. As a result, the puck will experience a net force and acceleration. The net force is referred to as a centripetal or inward force. Without such an internal force, an object would always move in the same direction and stay in a straight line. This will clarify the two situations where the puck was in position A and B.

Read more on centrifugal forces here:https://brainly.com/question/954979

#SPJ1

The spring constant of a spring that is compressed 5.0 cm and has 0.325 j of elastic potential energy stored in it is 13 N/cm.

What is the spring constant?

This is because of the spring constant:

k = (2 * elastic potential energy) / (change in length)²

Where elastic potential energy is:

elastic potential energy = (1/2) * k * (change in length)²

Substituting the given values:

0.325 = (1/2) * k * (0.05)²

Simplifying:

0.325 = 0.00125k

Solving for k:

k = 0.325 / 0.00125

  = 260 N/m

  = 26 N/cm

Therefore, the spring constant of the given spring is 13 N/cm (since 1 N/m = 0.1 N/cm).

To know more about spring constant:

https://brainly.com/question/29975736

#SPJ11

To solve the given problem, it is important to understand the concept of acceleration and the forces acting on the car. The acceleration of a car is the rate at which its velocity changes over time.

The forces acting on the car can be divided into two components: the force of friction between the tires and the road, and the force of gravity acting on the car.

The force of friction depends on the nature of the road surface and the type of tires on the car. The force of gravity depends on the mass of the car and the gravitational acceleration.

Therefore, a = (μ - g)/m is the expression for the acceleration of the car.

To know more about acceleration click here:

https://brainly.com/question/30660316

#SPJ11

The average force applied to the ball is 200 N.

The average force applied to the ball is:

F = Δp/Δt

Where F is the average force applied to the ball

Δp is the change in momentum

Δt is the change in time

Change in momentum is given by the formula:

Δp = m * Δv

Where Δp is the change in momentum

m is the mass of the ball Δv is the change in velocity

Change in time is given as Δt = 0.01 s

The mass of the ball is 0.1 kg

The initial velocity of the ball is 20 m/s

The final velocity of the ball is zero because the ball has stopped.

Δv = -20 m/s

Substitute the values in the formula,

Δp = m * ΔvΔp = 0.1 * (-20)Δp = -2 Ns

F = Δp/ΔtF

= (-2 Ns) / (0.01 s)

F = -200 N

The negative sign in the result indicates that the direction of force is opposite to the direction of motion.

Learn more about the direction of motion here:

https://brainly.com/question/1674237

#SPJ11

When the first extension cord is replaced by the second then the voltage supplied to the appliance drops by 3.834 V.

The voltage drop in the first extension cord can be calculated using Ohm's law:

V = IR

where V is the voltage drop, I is current, and R is the resistance.

The voltage drop in the first extension cord is V = IR = (5.60 A) x (0.0760 Ω) = 0.4256 V.

The voltage drop across the second extension cord is also V = IR = (5.60 A) x (0.760 Ω) = 4.256 V.

Therefore, the voltage supplied to the appliance changes by (0.4256 V - 4.256 V) = - 3.8304 V when the first extension cord is replaced by the second.

Extension cords are useful for transferring power to areas where there are no outlets, and they can also come in handy in places where outlets are inaccessible. However, if you have two extension cords to choose from, the voltage drop in each cord can impact the amount of voltage supplied to the appliance.

Learn more about Ohm's law:

https://brainly.com/question/14296509

#SPJ11

Answer:

circular path, 10 rotation in 5 sec

frequency of rotation = 10/5 = 2

Explanation:

The frequency of rotation for an object moving around a circular path at a constant speed and making ten complete revolutions in 5 seconds is 2 Hz (Hertz). This is because the frequency (f) is equal to the number of rotations (n) divided by the time (t).

In this case, n = 10 and t = 5, so the frequency is f = n/t = 10/5 = 2 Hz.

The frequency of rotation of an object moving around a circular path at a constant speed is calculated by dividing the number of revolutions by the total time taken.

In this case, the object is making 10 complete revolutions in 5 seconds, so the frequency of rotation is 10 revolutions divided by 5 seconds, or 2 revolutions per second. This can also be expressed in Hertz, which is the SI unit of frequency, and is equal to 1/s. In this case, the frequency is 2 Hertz. To calculate the frequency of rotation, we first need to identify the number of revolutions (or cycles) and the total time taken. Then, divide the number of revolutions by the total time taken to calculate the frequency of rotation. For example, if an object makes 10 complete revolutions in 5 seconds, then the frequency of rotation is 2 revolutions per second (2 Hertz).

For more equations related to frequency of rotation.

https://brainly.com/question/30892716

#SPJ11

When you want to find the maximum speed with which a 1200- kg car can round a turn of radius 85.0 m on a flat road if the coefficient of static friction between tires and road is 0.60, you can use the following formula: v = sqrt(μrg).

Where:v represents the maximum speed with which the car can round a turn r is the radius of the turn g is the acceleration due to gravity, andμ is the coefficient of frictionIn this case, the mass of the car is 1200 kg and the radius of the turn is 85.0 m, while the coefficient of friction is 0.60.

To find the acceleration due to gravity, we can use the value 9.81 m/s². Therefore:v = sqrt(0.60 * 9.81 m/s² * 85.0 m) = 23.7 m/sTherefore, the maximum speed with which the 1200-kg car can round a turn of radius 85.0 m on a flat road if the coefficient of static friction between tires and road is 0.60 is approximately 23.7 m/s.

Read more about gravity:

https://brainly.com/question/940770

#SPJ11

An object becomes electrically charged when there is a transfer of electrons between two objects. Electrons are negatively charged particles that orbit the nucleus of an atom. When two objects come into contact with each other, some electrons may move from one object to the other. The object that loses electrons becomes positively charged, while the object that gains electrons becomes negatively charged.

This transfer of electrons can also occur without direct contact between the objects. For example, if a charged object is brought close to a neutral object, the electrons in the neutral object may be attracted or repelled by the charged object. This can cause the electrons in the neutral object to move around, resulting in a separation of charges and the object becoming charged.

Another way an object can become charged is through the process of induction. If a charged object is brought near a neutral object, it can induce a separation of charges in the neutral object. This happens because the charged object creates an electric field that attracts or repels electrons in the neutral object. The result is a separation of charges, with one part of the object becoming positively charged and the other part becoming negatively charged.

To store 12.0 C of charge, you would need a capacitor with capacitance of 1.20 F.

Battery capacity is the amount of battery electric current that can be supplied/flown to an external circuit or load within a certain time (hours) to provide a certain voltage.

The capacitance required to store 12.0 C of charge in a capacitor connected to a single 10.0 V battery can be calculated using the formula,

Q = CV

where Q is the charge, C is the capacitance, and V is the voltage. Rearranging this equation, we get,

C = Q/V

Plugging in the given values, we get,

C = 12.0C/10.0V = 1.20 F

Therefore, the capacitance required to store 12.0 C of charge is 1.20 F (to three significant figures).

Learn more about battery capacity at https://brainly.com/question/30061793

#SPJ11

Errors due to earth curvature and refraction can be eliminated from the differential leveling process by using the trigonometric leveling method.

This method utilizes the principle of triangles to determine the height difference between two points on the Earth's surface.

The trigonometric method begins by measuring the horizontal angle between two points, then the vertical angle between the same two points, and finally the distance between the points.

The trigonometric method is not affected by the curvature of the Earth or refraction since the vertical angle is measured at a given distance instead of the line of sight.

Therefore, the measurements of the angles and distances remain unaffected.

The trigonometric leveling process is as follows: first, an instrument is set up at point A. A second instrument is then set up at point B, and both instruments are leveled.

The horizontal angle between the two points is then measured with a theodolite, followed by the vertical angle. Lastly, the distance between the two points is measured using a tape measure.

After all the measurements are taken, the results are then used in a trigonometric formula to calculate the difference in elevation between the two points.

This method eliminates errors due to refraction or the Earth's curvature, since the elevation difference is not determined by the line of sight, but rather by the measured angles and distance.

The trigonometric leveling method is the best method to eliminate errors due to the Earth's curvature and refraction from the differential leveling process.

This method uses trigonometric principles and measurements to accurately calculate the difference in elevation between two points.

to know more about refraction refer here:

https://brainly.com/question/14760207#

#SPJ11

The acceleration of the basketball would be the same as the tennis ball, 10 m/s2. This is because in this scenario, the acceleration of the two objects is determined by the same force, and not the mass of the object.

Acceleration is the rate of change of an object's velocity given by the equation a = F/m, where F is the force applied, and m is the mass of the object. Since the force is the same in both cases, the acceleration of the two objects must also be the same. This means that the basketball, which has a mass of 0.58 kg, will still accelerate at 10 m/s2.

Know more about Acceleration here

https://brainly.com/question/12550364#

#SPJ11

When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.

This is due to the fact that the speed of sound is proportional to the square root of the ratio of the bulk modulus to the density of the medium in which it travels.

When the density of the medium inside the pipe increases, the velocity of sound decreases, causing the frequency of the normal modes to decrease.

he wavelength of the sound waves inside the pipe is shortened due to the increase in density, resulting in a lower frequency of the normal modes.

The frequency of the normal modes of a pipe is influenced by a variety of factors, including the diameter and length of the pipe, as well as the speed of sound in the medium inside the pipe. T

he frequency of the normal modes is inversely proportional to the length of the pipe, with longer pipes producing lower frequencies.

In the case of a pipe filled with a liquid of higher density than air, the frequency of the normal modes would be lower than if it were filled with air.

This is because the speed of sound in the liquid would be lower than in air, resulting in a decrease in the frequency of the normal modes.

When a pipe is filled with a liquid of higher density than air, the frequency of the normal modes of the pipe decreases.

This is due to the fact that the speed of sound in the liquid is lower than in air, resulting in a decrease in the frequency of the normal modes.

to know more about frequency refer here:

https://brainly.com/question/14316711#

#SPJ11